(¥210) £209.79 exc vat
(¥252) £251.75 inc vat
In stock
Complete with rear loom for electronic fuel pump.
Basic spec is: centre speedo oval dash, single stalk, toggle or mk3 rocker switches, inertia starter, ...
(¥210) £209.79 exc vat
(¥252) £251.75 inc vat
In stockRecommended usage 1 x 5L1331 to fit one mini.
Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.
Rear body harness with speaker wires, known as thick wall type which was replaced by thin wall PVC covered wire type in 1989. AN169 is the thin wall equivalent and occassionly fitted or found on early cars wothout any problems.
...
You should always use this kit for fitting any auxiliary spot or fog lamps.
Kit contains wiring and safety relay-cheaper than a burnt out engine compartment.
Please note, SPI and MPI cars have this facility built as standard safety ...
Inertia starter -no side repeaters on wing -Instrument cluster in front of driver,either 3 clock with tacho or 2 clock cars but ignore wires from distributor for tacho and tacho wires.
On pre 1984 cars the wiring for the indicator...
All Minis require an earth strap from the engine to the body and from 1959-1996
they fitted from the gearbox to the subframe. When they introduced the twin point in 1996 it was moved to the upper engine stabiliser arm. About 13"LONG.
When replacing the 520160A parking switch the inner contact areas on the wiring loom are also worn or damaged so we produced this socket and small length of loom.
Universal post type battery earth strap with clamp type fitting and correct length for most alternatives of batteries fitted.
The battery cover made of a special cardboard as fitted to all minis to protect
the battery terminals from metal objects. See also the 14A7666 retaining strap.
This is the wiring short conversion loom that fits to the old central speedo and is used by people modifying from 2 or 3 clock dashes to single clock or just repairing damaged looms. With the correct bulb holders and spade fittings. Now uses 5x [link...
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
998cc minis with central speedo and alternator from 1972-75. This is a front loom only.
The only battery cable to run the full length of the Mini, this has a positive type terminal that clamps arond the post rather than the helmet or cap type on much earlier cars. Some cars had slightly shorter cables than this but measure your old cabl...
Basically just the rear lamps and number plate lamp wiring loom for mini van.
PVC covered rear loom only for Mk2 with heated rear screen.
Can be fitted to MK3 front loom ( HAM2174 ).
Braided rear part loom ONLY for MK1 Minis without a rear heated screen.
PVC covered loom for 1275GT models with alternator from 1970 to 1976. For dynamo version of this see AN127.
Basic spec is: side instrument pack, single stalk, MK3 rocker switches, round single speed wiper motor, manual washer pu...
Large grommet to fit 1"approx holes in bulkhead for items that need to be able to flex and move such as capillary tubes and oil pipes. 7/32" hole size.
The small hole will expand and is also used as wiring loom through bulkhead and battery c...
Braided cloth wiring loom for Cooper S MK1 with alternator. See 5L518 for braided with dynamo.
Complete with rear loom.
Cars with pre engaged starter,side repeater lamps on wings, dim dip unit pre Ocober 1988 production cars without servo and brake combined cylinders. R/H/D.
Original HAM4626 has pinkish brown resistance wire for ballast type coil...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.