STRAIGHT CUT 1st MOTION SHAFT 19 teeth
C-22A1732

($95.25) £95.25 exc vat

($114.30) £114.30 inc vat

In stockIn stock
STRAIGHT CUT FIRST MOTION GEAR FOR PRE A+ GEARSET

19 teeth



See table of "Straight Cut Gear Kits" and their components

($95.25) £95.25 exc vat

($114.30) £114.30 inc vat

In stockIn stock

Recommended usage 1 x C-22A1732 to fit one mini.

Recommended products
1ST MOTION SHAFT NOSE CIRCLIP (PILOT ROLLER)
CCN110

The little circlip on the end of the 1st motion shaft that holds the inner race

of the pilot bearing AAU8424. The larger circlip to hold the outer track in the clutch case is 2A3643.

($1.61) £1.61 exc vat

($1.93) £1.93 inc vat
ROLLER 1ST MOTION SHAFT PILOT TO CLUTCH CASE GENUI...
AAU8424

Genuine RHP Outer support bearing for the first motion shaft. Comes with bearing and outer race. You MUST REPLACE the outer race when using the new bearing. An easy way to remove the old race is to clean the housing very well, remove the circlip, and...

($28.23) £28.23 exc vat

($33.88) £33.88 inc vat
PRE A+ 1ST MOTION NEEDLE ROLLER.
CHM172

This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.

This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...

($3.75) £3.75 exc vat

($4.50) £4.50 inc vat
SINGLE ROW RHP ROLLER. 4 SYNCHRO
ADU7619

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

($34.97) £34.97 exc vat

($41.96) £41.96 inc vat
People also bought products
STRAIGHT CUT 1st GEAR 29 TOOTH
C-22A1735

STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET.



See table of "Straight Cut Gear Kits" and their components

($54.35) £54.35 exc vat

($65.22) £65.22 inc vat

GEAR REVERSE STRAIGHT CUT FOR ROD CHANGE ONLY
C-STR303

Straight cut reverse gear for rod change box. Has 16 and 18 teeth.



See table of "Straight Cut Gear Kits" and their components

($73.47) £73.47 exc vat

($88.16) £88.16 inc vat

GEAR STRAIGHT CUT LAYGEAR 4 SYNCROMESH PRE A PLUS ...
C-22A1737

In 4 synchro gearbox it's a critical part of the close ratio gear set. Be sure to check your old one for wear on the inner surface of the layshaft bearings; it wears out far faster than the gear teeth! Pre A+. For A Plus see C-22A1737A 1...

($105.02) £105.02 exc vat

($126.02) £126.02 inc vat
GEAR STRAIGHT CUT 3RD 22 TOOTH
C-22A1733

STRAIGHT CUT 3RD GEAR FOR 4 SYNC SPECIAL TUNING GEARSET

If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undoe the large mainshaft and Ist motion nuts,...

($83.70) £83.70 exc vat

($100.44) £100.44 inc vat
GEAR STRAIGHT CUT LAYGEAR A PLUS 4 SYNCHRO ST RATI...
C-22A1737A

LAYGEAR STRIGHT CUT FOR A PLUS GEARBOX IN ORIGINAL ST RATIO

TOOTH COUNT 15-19-23-25---this takes 2-CHM141 bearins

See table of "Straight Cut Gear Kits" and their components

($105.02) £105.02 exc vat

($126.02) £126.02 inc vat

23 TOOTH STRAIGHT CUT PRIMARY GEAR
C-STR123EVO

Evolution Straight cut 23 tooth 1275 primary gear.



Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares have introduced new EVO straight cut drop gears. With new 2 r...

($125.76) £125.76 exc vat

($150.91) £150.91 inc vat
LAYSHAFT A PLUS PERFORMANCE
C-22A1739

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

($31.85) £31.85 exc vat

($38.22) £38.22 inc vat
INPUT GEAR 25 STRAIGHT CUT
C-STR250

Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 ...

($40.16) £40.16 exc vat

($48.19) £48.19 inc vat
LAYSHAFT 4 SYNC COMP HIGRADE ( PRE 3 STEP . PRE A ...
C-22A1738

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...

($29.12) £29.12 exc vat

($34.94) £34.94 inc vat
IDLER GEAR A PLUS STRAIGHT CUT
C-STR30A

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1


24...

($48.38) £48.38 exc vat

($58.06) £58.06 inc vat
OUTPUT SHAFT CIRCLIP FOR LSD HARDY SPICER SHAFT
CCN122

Special circlip to hold the hardy spicer output shaft into the LSD units

such as evolution and Salisbury.

($1.16) £1.16 exc vat

($1.39) £1.39 inc vat
GEAR EVOLUTION A PLUS 1ST MOTION SHAFT 20 teeth
C-STR293A

20 tooth straight cut teeth 1st motion shaft for our famous Evolution gear kit C-STN39 .Molybdenum

coated baulk ring surface

($127.20) £127.20 exc vat

($152.64) £152.64 inc vat
GEAR EVOLUTION 3rd.23 TOOTH STRAIGHT
C-STR292

23 tooth straight cut gear teeth 3rd gear for our famous Evolution gear kit C-STN39. Molybdenum coated to the highest spec avaialble on the bailk ring surface.

($79.04) £79.04 exc vat

($94.85) £94.85 inc vat
MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...
AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

($26.00) £26.00 exc vat

($31.20) £31.20 inc vat
GEAR LEVER BUSH
22G389

The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise



fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play

($3.50) £3.50 exc vat

($4.20) £4.20 inc vat
CROWNWHEEL + PINION 3.2 RATIO 19/61 teeth
CWP3-2

61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)

A plus gears giving 3.211 ratio.

($157.50) £157.50 exc vat

($189.00) £189.00 inc vat
PRIMARY GEAR SHIM 998 114"-116"
22A323

Primary gear thrust washers are made in varying sizes to take up the play.

Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc

engines with 22A1493 Deva bush primary gear. Early 850cc had thin...

($18.30) £18.30 exc vat

($21.96) £21.96 inc vat
BEARING FOR IDLER GEAR CONVERSION ROLLER A+ TO PR...
DAM3745

THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...

($15.50) £15.50 exc vat

($18.60) £18.60 inc vat
REMOTE HOUSING SHORT BOLT 3/8" x 1" UNC
GFK5240

Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.

Also the bolt to hold the starter motor.

Also the bolt for the [...

($0.32) £0.32 exc vat

($0.38) £0.38 inc vat
LSD OUTPUT SHAFT RETAINING WASHER
C-BTA1243

Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.

($2.24) £2.24 exc vat

($2.69) £2.69 inc vat