£9.90 exc vat
£11.88 inc vat
In stock
£9.90 exc vat
£11.88 inc vat
In stockRecommended usage 1 x AUD1250 to fit one mini.
The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...
Not fitted as standard to the A seriers it found its way on engines as a great tuning aid on tuned engines. this is the spindle only and the disc is WZX1321.We suggest you use a complete rebuild kit if this area has worn-CRK223 which will have to be ...
Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...
This is the original type of needle valve that governs the plastic fuel float in your SU carb.
An alternative better upgraded version is available as CA90.
Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.
Carb to manifold spacer with facility for fitting a vacuum gauge. This is suitable for HS6 and HIF44 and is 6.3mm thick.
Throttle return springs for all twin carb variants. Usually 3 fitted.
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
For HIF Turbo only single carbs this is the very least of the parts required for an overhaul kit-if you require the spindle and disc and bushes see CRK269
Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the L/H ( front) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds- Midgets and MGB used different angles,u...
Mini Spares own performance upgrsded paper gasket that sits either side of the carb to manifold spacer on HIF38/44 type 1.75" carbs.Sold singly, order quantity as required to suit your car.
Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the R/H ( rear) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds-Midgets and MGB used different angles,usual...
Spacer with gaskets fitted for any 4 bolt fitting carb such as HS6 HIF range about 9/16" (14.5mm). As this is the only thick spacer you need to check stud length.
This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length (2.25"), some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the...
Latest design jet fitted to the HS6 carb, it had a metal base rather than plastic and was called a waxstat type.
Jet for twin HS6 carbs: The yellow band denotes left side/timing end carb. This is a 100thou jet.
Carb repair kit less spindle and butterfly for twin HS6 carbs-includes float needle valve and jet.
Cooper S Right Hand Tank. Our new perfect fit and shape tank is now in stock. No unsightly "stretch" marks as seen on other tanks that are available, this is a perfect authentic item we are proud of. Approx 5.5 gallon.
See MS82 ...
Special clip for all our braided s/steel petrol hoses.14mm to 16mm.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.