£500.93 exc vat
£601.12 inc vat
In stock
£500.93 exc vat
£601.12 inc vat
In stockRecommended usage 1 x C-BTA1226A to fit one mini.
New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17x59 teeth count.
Always Check...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.
Sold individ...
Bolt for holding the Clutch End cover (Wok) onto the flywheel housing.
Also for the CHM85 differential side cover 1" long unc 5/16" bolt.
A plus type bolt with built in washer on head, known as flanged head bolt.
Outputs for LSD when using inboard CV joints. Sold single with 2 needed per car.
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Stud to hold the clutch case to the engine and gearbox, 3 of required. 5/16"UNC thread for alloy fitment for gearbox with UNF thread the other end for the nuts. These are 1.5"long.
The 6 longer ones are 22A152.
These st...
Try these GENUINE MINISPARES superseal gearbox output shaft gaskets specially made to try and eliminate leaks.
Sold singly,2 per gearbox
This kit consists of one alloy sleeve with a groove on the outside to locate the O ring, the new "O" ring, a rod seal and a gaiter. To fit the kit simply remove the old gaiter if fitted and then the old oil seal. Fit the sleeve with the "O" ring fitt...
Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Upgraded version in Viton available us ADU5738VITON
Genuine RHP bearings. Not cheap Imported rubbish as sold under this part number.
This is the workhorse of the Mini gearbox. This double roller bearing supports the shaft where it transmits the power to the wheels. When this bearing goes, the...
A part that is historically known to fail over a period of time, due to contamination from road grit etc. Please also see part number MSSK050 for our modification kit to prevent future failures.
Mini Spares own square front sumpgurd adequate for road use and is cheaper and lighter than c-AJJ3320 RAC/Scottish type
made in alloy with fabricated side brackets for strength.weighs 4.885 kilos
also known as Monte Carlo sumpguard
Genuine Mini Spares latest state of the art Klinger material gasket, replacing 22A2237B for the clutch housing to help prevent oil leaks.
Measures 31 thou or 0.81 mm thick but compresses to correct size when fitted. Using l...
If you still have the original factory oil pick up pipe in your gearbox and not the C-AHT54 special pick up this is the oil seal that fits the pipe where it goes into the wire mesh strainer - this seal is not in gearbox gasket sets.
This is the 1st/2nd gear complete inner and outer hub assembly for all 4 synchromesh gearboxes. 33 teeth outer track
Gearbox gasket for the large alloy end cover which also houses the speedo drive pinion for all years of mini. The small gasket on the alloy housing with 2 bolt holes is GUG705564GM and the small pear shaped speedo housing gasket is [link...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.