£68.80 exc vat
£82.56 inc vat
In stock
£68.80 exc vat
£82.56 inc vat
In stockRecommended usage 1 x GRD974 to fit one mini.
Front mounted radiators on the twin point use 2 of these on the upper fitting prongs as mounting rubbers. The lower bush is EAP8708
Front mounted radiators use this lower mounting for location and to stop vibration -Fitted to twin point injection cars only
Upgraded aluminium radiator for mpi models which had the radiator mounted at the front as standard. Many MPI owners complain of their cars overheating and this super rad is one item to help overcome the problem. Radiator design has shown that horizon...
Upgraded aluminium radiator for mpi models which had the radiator mounted at the front as standard. Many MPI owners complain of their cars overheating and this super rad is one item to help overcome the problem. Radiator design has shown that horizon...
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
As fitted to MKI minis and variants. Original style tube of rubber material wrapped over a wire coil. As an improvement to the original design, these are also bonded to a nylon interior membrane for additional strength and the wire coil is galvenised...
Oil cooler union for later cars, will fit the oil filter head and block, 1/2" BSP to 11/16". Requires DSM18 to seal. These are handy when you have changed to a later filter head etc and want to fit an early oil cooler kit.
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
Spring clip for securing the top hose on MPI front mounted radiator models, now in stainless steel.
The heater is not available anymore, but this matrix is the main component which gets blocked up or leaks, stopping it blowing hot air.
This fits the early Mk1 cars only with 5" gap between pipe hole centres, after 1963 17H8608
Spring clip for securing the top hose on MPI front mounted radiator models.
This is the metric nut needed for PQR10028 tensioner as fitted to all mpi mini's.
m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)
original imperial radiator screws were SH604031 or PK type were ARA1117
Oil cooler kit for MPI models. Oil cooler is 10 rows, 21cm long and 9cm high. Unions are 18mm and require the special fitments as supplied in this kit. The oil filter is GFE210
Universal aluminium heater assembly complete with heater matrix and electric fan. Comes with 2 outlets for demisting windscreen and 2 variable vents for heating the rest of the car. Ideal for track/race cars or simply for those who want to replace th...
Silicone heater hose, 39" for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1988 cars.
Silicone heater hose, 39")1metre) for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.