MASTER CYLINDER PLASTIC CAP
513123A

($3.55) £3.55 exc vat

($4.26) £4.26 inc vat

In stockIn stock
Genuine plastic cap as supplied on single line brake cylinders pre 1976 and all clutch masters.

It doesn't often break or wear out but it gets lost or turns yellow. The early steel master cylinder reservoir caps had a tendency to rust on, so this white plastic could be considered an upgrade unless you wish to keep your Pre 1963 car original with a metal cap 17H3723

alsofits Midget and sprite and MGB 1963-79

($3.55) £3.55 exc vat

($4.26) £4.26 inc vat

In stockIn stock

Recommended usage 1 x 513123A to fit one mini.
Clutch & Pedal Linkage - Qty 1
Brake Pedal & Master Cylinders - Qty 1
Clutch cylinders and flywheel case - Qty 1

Recommended products

Extension piece in translucent white plastic screws on metal canister type master cylinders only. The seal provided slips over the thread of the filler neck and sits on the tank for the extension piece to screw down onto and seal. The original cap fi...

Alternative products

Replacement metal master cylinder cap as originally fitted to 1959-1963 Minis on single line brake systems is a great historic feature.

People also bought products

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Clutch master cylinder for all ADO16 models-Austin 1100/1300 and derivatives-

not for mini as the push rod is longer on this.

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

Braided one piece clutch hose from master cylinder to slave cylinder for left hand drive cars. Suitable for verto and pre verto clutch set ups, 91cm long.

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.

Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...

Suitable for standard 8.4" / 7.5" /7" brake calipers. Also used for front wheel cylinders on twin leading shoe type drum brake cars. This is where you have 2 cylinders per hub as opposed to the early single leading type which had one cylinder only pe...

Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use [link]...

This original metal canister master cylinder for Mini with Lockheed embossed on the can part has been available from us since August 2003 and are manufactured to OEM specification part number. Fitted with a plastic cap a metal original alternative is...

Gasket used under the dual master cylinder brake master cylinder. For the earlier single line brake pipe system see 31G279.

Rebuild kit (rubber) for early clutch slave cylinder GSY110 pre verto type. Early Spridgets are identified by a hard line runnung all the way to the slave cylinder. Later 1275's have a rubber hose to the slave cylinder.

one seal...

Clutch arm return spring for the return of the slave cylinder push rod. Total length 90mm.