($2.63) £2.63 exc vat
($3.16) £3.16 inc vat
In stock
($2.63) £2.63 exc vat
($3.16) £3.16 inc vat
In stockRecommended usage 1 x MYB100040 to fit one mini.
To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.
A more robust cast version on GEX7801.
Twin Down pipe clamp for Carb Coopers 1990 on wards, and Metro's.
Also used as a single clamp on manifold for cars fitted with HIF38 carb cars from 1991 on.
1.75" Bore centre exit twin tail pipe maniflow rear box with adaptor to sleeve down to the standard mini 998cc type exhaust system.
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Part of our millennium range of exhausts, this is the 200 Cell sport cat.
Catalytic converter will fit all mini models and if you require new studs the part number is FB110351 and the nuts to fit the studs are NV110051<...
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Injection models-Standard bore Budget priced LCB (1-3/4"id).
With pre cast flanges to improve flow and save engine tuners time matching the ports. This is for injection type cars only because it has a sensor hole. The Long Centre Branch des...
Standard single box silencer exhaust for the 850/998cc saloon.
Now designed by our RC40 team as a 2 piece system for easier fitment and transportation, this fits from the original cast iron inlet/exhaust manifold
right ...
Original exhaust bracket for rod change gearbox but later on Rover reverted back to GEX7526 which seemed a bit of a backward cost cutting exercise.
THE M10 METRIC NUT THAT SCREWS ON THE THREAD BOLTS OF THE CATALYLITIC CONVERTER
Exhaust centre strap that hangs from the mounting on the centre of the rear subframe, for saloon models only as the van is longer(GEX7273).
The clip on the exhaust that this attaches to is GEX7052 and is usually on a new exhaust...
Middle exhaust mounting, bolts on to the front of the rear subframe and is the central or first of the rubber mountings. see GEX7081POLY for Poly type or if you are fed up with breakages see C-19G3257.The original Genuine pa...
The long wheel base of the Mini Van, Wagon and Pick-up means the popular RC-40 exhaust comes up a little short! This system from Maniflow (pipes, resonator and muffler), is made for the long bodies. It has the same great flow characteristics of the ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.