(6,60 €) £6.60 exc vat
(7,92 €) £7.92 inc vat
In stock
After lengthy tests we have found nearly all vac units are not to the originals but with the change of added oxygenates to petrol in the 1980's and then ethanol in 2003 all previous economy and timing figure applications became incorrect. Nearly every after market vac unit checked appear to be similar to 37H8225/8226 without any distinguishing marks for identification.
Mini Spares now have a range of distributors to work with correct simplified vac units as ethanol leans off perol making engines run weak. The new vac units are designed for our distributors and as good as anything else being sold on the market to match old distributors as well.
Very few 850/998cc owners get their ignition and vac poundage checked out so many people are not aware of the power or economy losss.
For 850/998/1098 we use 37H8414MS for 45d and 59
for 1275cc we use 37H8379MS for 45d and 59d
(6,60 €) £6.60 exc vat
(7,92 €) £7.92 inc vat
In stockRecommended usage 1 x 37H8414MS to fit one mini.
Fitted from 1974 to 1980 for 45D distributors. Ethanol in petrol leans the air/petrol mixture making engines run leaner so see [link]37H8414MS[link].
After lengthy tests we have found nearly all vac units are not to the originals, but with t...
A kit to convert the early style cartridge oil filter to the later style spin on filter.
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102
This is the large seal for the early type oil filter assembly pre spin on type.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Stabiliser bush kit for lower engine steady
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Sports coil for ballast resistor type ignition.
Best internal parts tested and another intermotor top product.
Its not the name on the outside but whats on the inside which matters.
Original type coil bracket 12G29...
Parts required to stop timing chain rattle on A plus engine using special anti stretch single row chain 3H2127EVO.Last chance to buy with the plate and pin to hold the tensioner as they are obsolete from Rover.
Fitted to 998/110...
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
rear stop and tail lamp for early BMc cars with red plastic lens.
Also stocked is a white lens and single filament bulb equivalent for use as reverse light on kits cars and Mokes as CHM13REVERSE.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.
For those very early 25D type distributors.Mini Spares version for modern fuels as fitted to our distributor range with slide on vaccum hose inlet pipe-not the very first screw in type
best plug for 12g295 head as fitted to 998 cooper--for tuned head use B7ES.
this is good for any head where a lot has been machined off-flat top pistons.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.