(299,00 €) £299.00 exc vat
(358,80 €) £358.80 inc vat
In stock
(299,00 €) £299.00 exc vat
(358,80 €) £358.80 inc vat
In stockRecommended usage 1 x GXE1005EVO to fit one mini.
Small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.
Small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.
1.0 KW steel gear reduced unit, that draws less current from the battery when starting. Huge increase in comparison to the original units, and are a direct replacement part for the original pre-engaged starter motor.
Not ...
Best quality available-there are so many unreliable imports we have gone to Intermotor one of the original suppliers since the demise of original Lucas.
The activation of the starter motor starts with the key (or push button in the early car...
This new modern high-torque pre-engaged starter is used on all Minis 1985-on.
Should only be used with the correct corresponding ring gear PSF10003 which has 129 square section teeth. These units are now sourced brand new, no o...
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
Stainless steel coil bracket for 1970-1996 cars.
Lightweight competition alternator for all pre 1997 mini's. This unit weighs 3.2kgs and outputs 55 amps. Designed as a direct bolt on replacement but features a multi position mounting bracket so ideal for race cars/custom applications also. Does not...
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
Bracket for attaching the Distributor water shield block to gearbox stud/bolt
Does not come with fixing clips, these are available seperately as part number 13H6461
Upper bracket-NJU10002
Lower bracket- JZV1073
The...
Fits metal headlamp bowl to fix headlamp outer rim, sold singularly.
A working car horn is not only a necessity it is also a legal requirement in England and most other countries.This the single spade terminal with an open trumpet
Almost any screw will hold the chrome headlamp bezel on, but only one is correct! These screws are stainless steel and will never corrode plus they have the little rubber washer on the backside so that the screw will not fall out when trying to fit ...
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
Original manufacturer LESS THE GEAR 608092A this same wiper motor has been fitted since the late Mk2 version 1968/9 and is still used on the latest twin points but is wired up to give 2 speed and intermittent wipe.
The gear is ...
The original blue rotor arm was fited with a blue cap GDC143 to the turbos and were made stronger by moulding and riveting the contact plate to the arm, so if you are looking for an upgrade on your 45D body distributor this is our altern...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.