GEAR EVOLUTION LAYGEAR A PLUS
C-STR294

£142.40 exc vat

£170.88 inc vat

In stockIn stock
laygear for our famous C-STN39 straight cut gear set.

teeth count as follows 15-19-23-25--beware same teeth count on laygears as original Special Tuning gears but different widths--for identification purposes this gear takes only 1-CHM141 bearing and has a groove around the 3rd tooth of the laygear to show it is A PLUS Clubman ---the Special Tuning ratio gears have 2-CHM141 bearings fitted and no identification nmarkings

£142.40 exc vat

£170.88 inc vat

In stockIn stock

Recommended usage 1 x C-STR294 to fit one mini.

Kit products
this is an invalid number use C-STN39 A PLUS ONLY
C-STN38

was pre a plus clubman gear kit

£286.00 exc vat

£343.20 inc vat
People also bought products
LAYSHAFT A PLUS PERFORMANCE
C-22A1739

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

£31.85 exc vat

£38.22 inc vat
STRAIGHT CUT 1st GEAR 29 TOOTH
C-22A1735

STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET.



See table of "Straight Cut Gear Kits" and their components

£54.35 exc vat

£65.22 inc vat

GEAR STRAIGHT CUT A PLUS 1st MOTION SHAFT 19 teeth
C-22A1732A

STRAIGHT CUT FIRST MOTION GEAR FOR A+ GEARSET ORIGINAL ST RATIO

19 teeth



See table of "Straight Cut Gear Kits" and their components

£95.25 exc vat

£114.30 inc vat

GEAR REVERSE STRAIGHT CUT FOR ROD CHANGE ONLY
C-STR303

Straight cut reverse gear for rod change box. Has 16 and 18 teeth.



See table of "Straight Cut Gear Kits" and their components

£73.47 exc vat

£88.16 inc vat

IDLER GEAR A PLUS STRAIGHT CUT
C-STR30A

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1


24...

£48.38 exc vat

£58.06 inc vat
GEAR STRAIGHT CUT 3RD 22 TOOTH
C-22A1733

STRAIGHT CUT 3RD GEAR FOR 4 SYNC SPECIAL TUNING GEARSET

If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undoe the large mainshaft and Ist motion nuts,...

£83.70 exc vat

£100.44 inc vat
GEAR EVOLUTION A PLUS 1ST MOTION SHAFT 20 teeth
C-STR293A

20 tooth straight cut teeth 1st motion shaft for our famous Evolution gear kit C-STN39 .Molybdenum

coated baulk ring surface

£127.20 exc vat

£152.64 inc vat
GEAR EVOLUTION 2nd.26 TOOTH STRAIGHT CUT
C-STR291

26 tooth 2nd straight cut teeth gear for our famous evolution gear kit C-STN39. Molybdenum coated baulk ring surface.

£80.80 exc vat

£96.96 inc vat
GEAR EVOLUTION 3rd.23 TOOTH STRAIGHT
C-STR292

23 tooth straight cut gear teeth 3rd gear for our famous Evolution gear kit C-STN39. Molybdenum coated to the highest spec avaialble on the bailk ring surface.

£79.04 exc vat

£94.85 inc vat
PRIMARY GEAR BACKING RING GENUINE
88G549GENUINE

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

£13.00 exc vat

£15.60 inc vat
DIFF HOUSING LOCK TAB ROD CHANGE LH
42H500

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

£0.91 exc vat

£1.09 inc vat
DIFF HOUSING LOCK TAB ROD CHANGE RH
22A692

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

£1.35 exc vat

£1.62 inc vat
MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...
AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

£26.00 exc vat

£31.20 inc vat
GEARBOX LOCKTAB FOR 3 BOLT MAIN BEARING HOUSING/ S...
DAM6047

FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)

housing and deleted 1996 on.locking glue used such as locktite

£0.99 exc vat

£1.19 inc vat
SINGLE ROW RHP ROLLER. 4 SYNCHRO
ADU7619

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

£34.97 exc vat

£41.96 inc vat
COMPETITION STEEL BAULK RING
C-22A1741

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...

£35.36 exc vat

£42.43 inc vat
DIFFERENTIAL ROLLER RHP manufacture
AHU1856

Genuine RHP as originally fitted to every production Mini.

Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.

Some original fi...

£28.29 exc vat

£33.95 inc vat
BALL BEARING FOR SYNCHRO HUB 3&4 SYNCHRO
BLS107

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

£0.45 exc vat

£0.54 inc vat
GEARBOX GASKET SET(GUG708010TS)
AJM804B

Mini Spares own Gearbox gasket set for all manual Mini transmissions. It does not include the clutch oil seal 13H2934 or output shaft seals ADU5738 or 13H577 selector shaft seal for pre rod change gearbox becaus...

£8.88 exc vat

£10.66 inc vat
COPPER SUMP PLUG AND BLOCK WASHER
AED172

Mini Copper Sump Drain Plug Washer, also will fit the oil transfer pipe block fitting on Pre 1992 Blocks.

£0.79 exc vat

£0.95 inc vat