(¥278) £277.50 exc vat
(¥333) £333.00 inc vat
(¥278) £277.50 exc vat
(¥333) £333.00 inc vat
Recommended usage 1 x C-27H7773 to fit one mini.
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For any...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
This distributor clamp should not be bent; if it is, either you can't get the dizzy all the way in or it won't grip.
Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...
Electronic ignition conversion. For point type 25/23D distributors Negative earth only. For positive earth systems use LU142AP12.
ONLY use GCL217 coil for ballasted systems (1982 to 1993 998cc) or GCL216 coil for non-ballasted systems DO NOT...
Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
A PLUS ONLY
Replac...