GEAR STRAIGHT CUT A PLUS 1st MOTION SHAFT 19 teeth

C-22A1732A

($95.25) £95.25 exc vat

($114.30) £114.30 inc vat

In stock

STRAIGHT CUT FIRST MOTION GEAR FOR A+ GEARSET ORIGINAL ST RATIO

19 teeth

See table of "Straight Cut Gear Kits" and their components

($95.25) £95.25 exc vat

($114.30) £114.30 inc vat

In stock

People also bought products

STRAIGHT CUT 1st GEAR 29 TOOTH

C-22A1735

STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET.

See table of "Straight Cut Gear Kits" and their components

($54.35) £54.35 exc vat

($65.22) £65.22 inc vat

GEAR REVERSE STRAIGHT CUT FOR ROD CHANGE ONLY

C-STR303

Straight cut reverse gear for rod change box. Has 16 and 18 teeth.

See table of "Straight Cut Gear Kits" and their components

($73.47) £73.47 exc vat

($88.16) £88.16 inc vat

GEAR STRAIGHT CUT LAYGEAR 4 SYNCROMESH PRE A PLUS ...

C-22A1737

In 4 synchro gearbox it's a critical part of the close ratio gear set. Be sure to check your old one for wear on the inner surface of the layshaft bearings; it wears out far faster than the gear teeth! Pre A+. For A Plus see C-22A1737A 1...

($105.02) £105.02 exc vat

($126.02) £126.02 inc vat

GEAR STRAIGHT CUT 3RD 22 TOOTH

C-22A1733

STRAIGHT CUT 3RD GEAR FOR 4 SYNC SPECIAL TUNING GEARSET

If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undoe the large mainshaft and Ist motion nuts,...

($83.70) £83.70 exc vat

($100.44) £100.44 inc vat

GEAR STRAIGHT CUT LAYGEAR A PLUS 4 SYNCHRO ST RATI...

C-22A1737A

LAYGEAR STRIGHT CUT FOR A PLUS GEARBOX IN ORIGINAL ST RATIO

TOOTH COUNT 15-19-23-25---this takes 2-CHM141 bearins

See table of "Straight Cut Gear Kits" and their components

($105.02) £105.02 exc vat

($126.02) £126.02 inc vat

IDLER GEAR A PLUS STRAIGHT CUT

C-STR30AEVO

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.

Evolution Straight cut 23 tooth 1275 primary gear.

Ongoing development and investment of bringing parts up to date from yesturyear with current tec...

($75.28) £75.28 exc vat

($90.34) £90.34 inc vat

INPUT GEAR 24 TEETH STRAIGHT CUT

C-STR240EVO

Evolution Straight cut 24 tooth input gear.

These gears are banded with 2 rings for identification.

Do not mix and match with other gears that have same teeth counts unless they have the same 2 identification bands

...

($64.08) £64.08 exc vat

($76.90) £76.90 inc vat

INPUT GEAR 23 TEETH STRAIGHT CUT

C-STR230EVO

Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.

Achievable drop gear ratios ...

($64.08) £64.08 exc vat

($76.90) £76.90 inc vat

23 TOOTH STRAIGHT CUT PRIMARY GEAR

C-STR123EVO

Evolution Straight cut 23 tooth 1275 primary gear.

Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares have introduced new EVO straight cut drop gears. With new 2 r...

($125.76) £125.76 exc vat

($150.91) £150.91 inc vat

LAYSHAFT A PLUS PERFORMANCE

C-22A1739

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

($31.85) £31.85 exc vat

($38.22) £38.22 inc vat

LAYSHAFT 4 SYNC COMP HIGRADE ( PRE 3 STEP . PRE A ...

C-22A1738

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...

($29.12) £29.12 exc vat

($34.94) £34.94 inc vat

IDLER GEAR A PLUS STRAIGHT CUT

C-STR30A

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.

Achievable drop gear ratios when using our Evolution gears:

22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1

24...

($48.38) £48.38 exc vat

($58.06) £58.06 inc vat

GEAR EVOLUTION LAYGEAR A PLUS

C-STR294

laygear for our famous C-STN39 straight cut gear set.

teeth count as follows 15-19-23-25--beware same teeth count on laygears as original Special Tuning gears but different widths--for identification purposes this gear takes onl...

($142.40) £142.40 exc vat

($170.88) £170.88 inc vat

IDLER NEEDLE ROLLER BEARING FOR A PLUS GEARBOX IKO

TUK100320-IKO

IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...

($7.20) £7.20 exc vat

($8.64) £8.64 inc vat

DIFF HOUSING LOCK TAB ROD CHANGE LH

42H500

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

($0.91) £0.91 exc vat

($1.09) £1.09 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

($26.00) £26.00 exc vat

($31.20) £31.20 inc vat

BAULK RING TO ORIGINAL ROVER SPEC PRE 2000

22G2033EVO

Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...

($13.23) £13.23 exc vat

($15.88) £15.88 inc vat

GOLD MAGNETIC SUMP PLUG

DP3

Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...

($20.10) £20.10 exc vat

($24.12) £24.12 inc vat

RIGID ENGINE TO GEARBOX HALF MOON SEAL U

CAM6548

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

($4.00) £4.00 exc vat

($4.80) £4.80 inc vat