SUMP PLUG WITH TAPER FOR GEARBOX REPAIR
DP2

($8.87) £8.87 exc vat

($10.64) £10.64 inc vat

In stockIn stock
If you have stripped or ruined the sump plug thread in your gearbox, you have 2 easy alternatives. You can have a helicoil fitted or use this self cutting taper thread plug which must only be tightened enough without use of a washer to hold in the oi...

($8.87) £8.87 exc vat

($10.64) £10.64 inc vat

In stockIn stock

Recommended usage 1 x DP2 to fit one mini.
Gearbox Transmission Case 2 - Qty 1

Alternative products

Original Sump Drain Plug, with magnetic pick up. The washer for this is AED172.

If this original sump plug has stripped the thread in the block try our self threading plug DP2. Always thoroughly clean the magnetic part when doin...

Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all manual Mini's.

People also bought products

IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...

USED old and slightly rusty but usable-This is the later differential cast type cage which takes the planet gear thrusts DAM5071 that have a lip on as per all later A plus gearboxes.Other than the recesses to accept the later thrust wash...

Kit which enables you to fit a rod change gearbox to an earlier round tunnel.

Full rebuild kit less diferential parts with competition layshaft and EVO baulk rings.

Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. <...

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...

Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...

Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.

Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

Full rebuild kit with dihferential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...

A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105

59 tooth crownwheel plus 20 tooth pinion making 2.95 ratio. A plus gears sold as a set only.

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

Genuine Mini Spares product, fits 3 and 4-synchro gearboxes except for rod change types which use GAE191. This switch replaces the plug on the front of the remote-shift transmission case. It is triggered internally by the shift linkage w...