HEAD STUD BLOCK TO HEAD LONGER TYPE OF SHORT FRONT...
TAM1617

($6.75) £6.75 exc vat

($8.10) £8.10 inc vat

In stockIn stock
This A type block 3/8" unc

stud to retain the cylinder head is 11/16"(17.3mm) longer than the standard 4" type with 1.5" of thread to hold brackets for other ancillaries such as coil. Usually fitted only at the heater tap end of the cylinder head. If using 51K282 you will need spacers/washers under the nuts as it only has 3/4" thread.

Gearbox differential housings also used this stud and reference chart as follows:



Remote type case

53K266 are 4.5" long - 4 for remote now use TAM1617

53K1471 are 3" long 5/16" unc x3 or use 51K885

Rod change gearbox used-

22G1834 are 4.5" long 3/8" unc with 0.375" thread rod change only x2 - use 51K282

CHS2624 are 3" long 3/8" unc with 0.250" thread x3 or use BH506181 bolt

($6.75) £6.75 exc vat

($8.10) £8.10 inc vat

In stockIn stock

Recommended usage 1 x TAM1617 to fit one mini.
Block Components & Pistons - Qty 1
Gearbox Transmission - Qty 4
Engine and Block 1275cc - Qty 1

Recommended products

Correct latest spec head nut.Beware many sell an inferior nut.

Fitted to A Plus on, the built in flange of this latest specification multi point nut helps to spread the load and improve clamping force.

They may be used on any A-...

Standard A-series cylinder head retaining nut. For the later flanged nut see part number CAM4545.

Alternative products

The 8 port head is taller than standard A series heads so these MGB short head studs are used on the front--4 3/8" long 3/8" UNC stud with unf end for head nut. These studs are also used for rod change gearbox differential housings.

[link}53...

You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...

People also bought products

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.

The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...

Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:

Inlet/Exhaust manifold to head, studs/nuts/washers

Thermostat housing (no sandwich plate) studs/nuts/washers

H...

Complete nut, bolt and washer set for engine to gearbox only

Minispares own stainless steel manifold stud and 6 sided hexagon nut kit.

For mutipopint nut kit see C-STR287

Quantity required one kit per car

Minispares own stainless steel Thermostat housing stud kit for the single tier type thermostat housing.Quantity required one kit per car

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.

This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket

A true Cooper S engine has 10 studs and one specially designed bolt.

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

replacements in stainless steel for the heater tap elbow on the cylinder head.

Quantity required one kit per car

There are 3 of these bolts fitted -1.75"long 5/16"UNF bolt ALTERNATIVE DAM7758.

Also used as longer bolt for water pump.

Also for the 21A1091 heavy duty tie rods on front suspension.

Chrome Rocker bolt with UNF thread. Original Rocker cover bolts are dull zinc coated or painted but the chrome type look much better and cheaper.

A longer threaded version CAM6823 was used on prestige Minifin alloy type A series...

This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...

A simple way to dress up that engine compartment while at the same time insuring all the proper hardware is in place. A kit includes 2 each of British made chrome sleeve nuts, spacers and special cup washers, Fits all A & B series engines.

F...

Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...

Longer main bolt stud.

As supplied with our main strap kit.

The larger 5/16 unf size rocker screw as used on all forged, sintered and later pressed steel versions that use AEG167 screw in EN8 with heat treated ends. 1/2" wide AF spanner size head nut to fit AEG167

See [link]...