($45.00) £45.00 exc vat
($54.00) £54.00 inc vat
In stock
these...
($45.00) £45.00 exc vat
($54.00) £54.00 inc vat
In stockRecommended usage 2 x DAM3114 to fit one mini.
Circlip that fits on the gearbox output shaft in the differential for the pot joint type cars. Sold singly 2 required per gearbox.
Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...
Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Upgraded version in Viton available us ADU5738VITON
Hardy Spicer Adapters to convert pot joint output shafts to fit a hardy spice coupling (will also fit the Quaife ATB)
Pair of driveshafts to suit ADO16 / Austin 1100. these shafts are made to accept a GCV1102MS pot joint so that later mini engines and gearboxes can be easily fitted into ADO16's without the need to fit the early rubber cross type drive c...
Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.
These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)
A plus gears giving 3.211 ratio.
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
59 tooth crownwheel plus 20 tooth pinion making 2.95 ratio. A plus gears sold as a set only.
Non genuine aftermarket only as the genuine originals are obsolete.
These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle; this is ...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
Crownwheel with 58 teeth and pinion gear with 21 teeth. Not supplied with bearings.
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the left hand short one.
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the right hand longer one.
IF YOU EVER STRIP ONE OF OUR C-AJJ3385 CROSSPIN DIFFS DOWN THIS IS THE SHORTMOLYBDENUM COATED PIN THAT A PLANET WHEEL RUNS ON.
There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number GFK3431.
Sold Individually.
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
In board CV joint(pot joint) gaiter kit with plastic clips and grease.
Non Genuine item many sell as GSV1073.
The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one ver...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.