($21.75) £21.75 exc vat
($26.10) £26.10 inc vat
In stock
If both engine block bolts for the engine stabiliser bar are broken and there is no breather fitted use MSSK004
If a breather is fitted on the clutch housing and only the longer engine block bolt is broken use MSSK003
If a breather is fitted and both the engine block bolts are broken use MSSK005
Please note this kit will only fit manual cars.
($21.75) £21.75 exc vat
($26.10) £26.10 inc vat
In stockRecommended usage 1 x MSSK005 to fit one mini.
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980...
Complete nut, bolt and washer set for engine to gearbox only
Price per rod-1275cc larger 6.35mm diameter push rod. Sold per single rod and 8 required per engine.
The larger diameter improves push rod rigidity as much as possible
without having to modify the block/head push rod ports. Thi...
I gallon 20/50 classic oil with original look jug from the 60s
Spin on oil filter housing for performance engines-uses 88G402 gasket-made out of billet alloy it has a strong mating face to the block where oil leakage occurs from high revving engine vibrations, is slightly shorter offering more clear...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Mineral oil especially formulated for the combined engine and gearbox such as the mini, but for better gearchange etc use MILERS002 except on rebuilt engines where pistons must be allowed to bed in using non synthetic oil. 5 litre bottle.
Se...
later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable
3/8"unc 1"long
Lower Stabilizer Kit, RH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In stock form the control is left to the upper stabilizer. This often results in not o...
A must if you want to run a mechanical oil gauge and retain the oil warning switch. Screws straight into the block on all A series engines.
Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.
A Plus camshaft
If you've done your reading, then you know that "Scatter Pattern" cams are designed specifically for the peculiarities of the A-Series engine with it's five-port head. By optimizing lobe centers and phasing for each cylinder,...
All "A" Plus and engines with metal tube to locate dipstick (no 850cc or Automatics). 227mm from mount face to full mark.
A design initiated by Keith Dodd as an easier to use alternative to the other engine oil dip sticks available with butt...
Mini Spares Non genuine timing chain gasket fitted to every BMC A series engine with 10 gasket holes until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.
Gasket material h...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.