(48,00 €) £48.00 exc vat
(57,60 €) £57.60 inc vat
Out of stock
(48,00 €) £48.00 exc vat
(57,60 €) £57.60 inc vat
Out of stock
This is the gear on the end of the 1st motion shaft that connects with the idler gear. 29 teeth for A plus only-----earlier models had 24 teeth.
MPI Mini /Metro late cars could have 28 teeth with a groove marking-part DAM6337
the ge...
A Plus idler gear-these are the last type made from what they call clean steel to eradicate power train wear and were used on multi points injection cars and work best with Torrington bearings TUK100320-these are priced less than half Rover retail. H...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17x59 teeth count.
Always Check...
Torrington/Koyo idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior...
Planet gears for the differential are now manufactured by us as the genuine Rover product is obsolete. Beware of others on the market which must be checked before fitting as the overall dimensions in height seem to vary along with inferior/wrong mate...
Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Upgraded version in Viton available us ADU5738VITON
A part that is historically known to fail over a period of time, due to contamination from road grit etc. Please also see part number MSSK050 for our modification kit to prevent future failures.
Minispares own Evolution limited slip diff with over 10 years success
General spec and design is the same as C-AJJ3387 but has a 45/45 ramp type giving drive on acceleration and deceleration, preferred by many rally drivers for ...
Genuine Mini Spares latest state of the art Klinger material gasket, replacing 22A2237B for the clutch housing to help prevent oil leaks.
Measures 31 thou or 0.81 mm thick but compresses to correct size when fitted. Using l...
Genuine RHP Outer support bearing for the first motion shaft. Comes with bearing and outer race. You MUST REPLACE the outer race when using the new bearing. An easy way to remove the old race is to clean the housing very well, remove the circlip, and...
Special pin to hold the differential cross pin in place in the housing.
See DAM3108 also for smaller diff shims. Refer to workshop manual for fitment.
Lower Stabilizer Kit, LH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In standard form the engine control is left to the upper stabilizer. This often result...
The latest model Mini differential still use thrust washers on the spider gears but now have a tab on one end to prevent them from rotating on the cage side of the diff. The cage of course is cast while the gear itself is much harder and thus the wh...
Gearbox differential pinion locktab to secure it on the mainshaft for all manual gearboxes.
Genuine Mini Spares product. Spacer fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear. Now made 2 thou oversize to help corect wear issues.
Only f...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.