24 TOOTH STRAIGHT CUT PRIMARY GEAR
C-STR124EVO

£125.76 exc vat

£150.91 inc vat

In stockIn stock
Evolution Straight cut 24 tooth 1275 primary gear.

Evolution Straight cut 23 tooth 1275 primary gear.



Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares h...

£125.76 exc vat

£150.91 inc vat

In stockIn stock

Recommended usage 1 x C-STR124EVO to fit one mini.

Recommended products

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

People also bought products

Idler gear conversion for straight cut drop gearsets only.

This set up is for A plus idler gearbox cases only and uses a single roller bearing centrally unlike the old timken conversion which had taper bearings either end.These gears are ba...

Idler gear conversion for straight cut drop gearsets only. This set up is for Pre A plus idler gearbox cases only and uses a roller bearing centrally unlike the old timken conversion which had taper bearings either end.



Evolut...

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.



Evolution Straight cut 23 tooth 1275 primary gear.



Ongoing development and investment of bringing parts up to date from yesturyear with current tec...

Straight cut drop gears are the most durable arrangment that can be fitted to a transverse A-series powerunit. These 3 gears are responsible for transferring all the Hp from the motor to the gearbox, so their longevity should be a top priority for an...

Evolution Straight cut 24 tooth input gear.

These gears are banded with 2 rings for identification.

Do not mix and match with other gears that have same teeth counts unless they have the same 2 identification bands


...

Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.





Achievable drop gear ratios ...

Evolution Straight cut 22 tooth 1275 primary gear.



Evolution Straight cut 23 tooth 1275 primary gear.



Ongoing development and investment of bringing parts up to date from yesturyear with current technology ...

Evolution Straight cut 23 tooth 1275 primary gear.



Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares have introduced new EVO straight cut drop gears. With new 2 r...

Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.





Achievable drop gear ratios when using our Evolution gears:



22 tooth primary - 30 tooth idler - 25 ...

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...

Straight cut gearset for A+ gearbox's using the standard 1st and reverse gear. UK made -The ultimate for TUNED street cars or clubman events giving nearly the same close ratios as the original 3 synchro straight cut gear set.

Using latest g...

Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.

Kit which enables you to fit a rod change gearbox to an earlier round tunnel.

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.

Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17/59 teeth cont

Not for LSD se...