£117.36 exc vat
£140.83 inc vat
In stock
2 ring identification and must be used with othe EVO components for drop gears.
£117.36 exc vat
£140.83 inc vat
In stockRecommended usage 1 x C-STR224EVO to fit one mini.
Idler gear conversion for straight cut drop gearsets only.
This set up is for A plus idler gearbox cases only and uses a single roller bearing centrally unlike the old timken conversion which had taper bearings either end.These gears are ba...
Idler gear conversion for straight cut drop gearsets only. This set up is for Pre A plus idler gearbox cases only and uses a roller bearing centrally unlike the old timken conversion which had taper bearings either end.
Evolut...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current tec...
Straight cut drop gears are the most durable arrangment that can be fitted to a transverse A-series powerunit. These 3 gears are responsible for transferring all the Hp from the motor to the gearbox, so their longevity should be a top priority for an...
Evolution Straight cut 25 tooth input/broach gear.
These gears are banded with 2 rings for identification.
Do not mix and match with other gears that have same teeth counts unless they have the same 2 identification bands
...
Evolution Straight cut 24 tooth input gear.
These gears are banded with 2 rings for identification.
Do not mix and match with other gears that have same teeth counts unless they have the same 2 identification bands
...
Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.
Achievable drop gear ratios ...
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x60 teeth count.
THIS IS THE ...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
Mini Copper Sump Drain Plug Washer, also will fit the oil transfer pipe block fitting on Pre 1992 Blocks.
Planet gears for the differential are now manufactured by us as the genuine Rover product is obsolete. Beware of others on the market which must be checked before fitting as the overall dimensions in height seem to vary along with inferior/wrong mate...
This kit consists of one alloy sleeve with a groove on the outside to locate the O ring, the new "O" ring, a rod seal and a gaiter. To fit the kit simply remove the old gaiter if fitted and then the old oil seal. Fit the sleeve with the "O" ring fitt...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.