WASHER PLAIN 5/16"
GFK1114

£0.06 exc vat

£0.07 inc vat

In stockIn stock
5/16" flat plain washer.

£0.06 exc vat

£0.07 inc vat

In stockIn stock

Recommended usage 1 x GFK1114 to fit one mini.
Cylinder Head Valve Sizes - Qty 3
Engine Components Cylinder Head - Qty 3
Timing Cover & Tappet Inspection Cover - Qty 4
Clutch Housing - Qty 1
Gear Change Up to 1972 Not Rod Change - Qty 3
Inlet & Exhaust Manifolds - Qty 2
Camshaft and Timing Chain - Qty 2
Timing, side plate and rocker covers - Qty 4
Timing, side plate and rocker covers - Qty 1
Water Pump and thermostat - Pre 1996 Not MPI - Qty 3
Inlet and Exhaust manifolds except Injection - Qty 6
Inlet and Exhaust manifolds for Injection Cars - Qty 2
Flywheel and Clutch - Qty 1
Exhausts for 998cc with HS4 and Cooper 1275 cc wit - Qty 1
Exhausts for 998cc with HS4 and Cooper 1275 cc wit - Qty 2
1275cc with HIF38 carburettor and open loop cataly - Qty 2
Power unit electrics Non Injection - Qty 1
Front Subframe - Qty 4
Front Subframe - Qty 4
Rear Subframe - Qty 8
Rear Subframe - Qty 4
Engine Mountings & Brackets - Qty 3
Alternators and Starter - Qty 1
Alternators and Starter - Qty 1
Cylinder Head - Qty 3

Kit products

Every nut, washer, bolt, rubber bush and 2 pins that hold the rubber bushes that are prone to rusting badly and are required every time you do a subframe change. Including the 2 large penny washers this kit has 36 components. Other companies offer l...

This is the kit supplied with our C-AHT772, C-AHT773 & C-AHT774 range of alloy inlet manifolds for the weber.

Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.

complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43

Rubber mounts are made in the UK.

Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:

Inlet/Exhaust manifold to head, studs/nuts/washers

Thermostat housing (no sandwich plate) studs/nuts/washers

H...

Conversion mount kit, with fittings to allow the fitment of a manual engine to an automatic front subframe.



Will require to elongate the 2 upper holes on subframe equally, once subframe holes line up with the spacer plate in this k...

This kit contains all the parts from MS44 plus the 4 cast trunnions that hold the rubber bushes. This complete rear subframe fitting kit is what the factory fitted to minis up to 1976 on but the later kit MS41 will fit early...

Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.

Front subframe fitting kit for pre 76 twin bolt subframes, locktabs are included but not the subframe tower spacers as these rarely need changing.

All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.

All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Engine mount bolt kit for manual cars, 1 kit requried per car.

People also bought products

Boot hinge gaskets and fittings for original type hinges

This kit includes all hardware to fit suspension to your front subframe. Also includes front damper mounting hardware and lower arm pins.

Shakeproof star washer 3/16"unf sold individually-order quantity as required

Fibre washer to go under 12A1436 metal washer on the twin HS2 carb air cleaner. One required for HS4--sold singly order as required

The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...

New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...

Flat 1/2" washer, 2.24mm thick approx.

Spring washer 7/16" x 11/16".Sold singly