($30.80) £30.80 exc vat
($36.96) £36.96 inc vat
In stock
Tube nut has 7 threads and the metal pipe is the same size with a flared end.
($30.80) £30.80 exc vat
($36.96) £36.96 inc vat
In stockRecommended usage 1 x WKB10018L to fit one mini.
From the introduction of fuel injection systems in 1992, a fuel filter was mounted on the rear subframe. These should be replaced every 2 years or 24,000 miles, whichever is the sooner.
GFE7059 covers all SPI models and MPI up to chassis nu...
From the introduction of fuel injection systems in 1992, a fuel filter was mounted on the rear subframe. These should be replaced every 2 years or 24,000 miles, whichever is the sooner.
GFE7059 covers all SPI models and MPI up to chassis nu...
This combined fuel filter and regulator allows adjustment of fuel pressure for optimum power and fuel economy.The inlet and outlet unions are universal for either 1/4" or 5/16" hoses. The FPR004 is a glass dome version of the alloy bodie...
Complete kit for fitting an MPI tank, including tank, pump, sender and seals.
Gasket for SPI throttle body spacer. 2 required
5/16" UNF THREAD 2 1/2" LONG bolt commonly used for 21A2838 petrol tank strap
7.5 gallon tank has both pump and sender unit holes for injection cars only. Some people use this tank for turbo applications however.
MPI 7.5 gallon tank has both pump and sender unit holes. Some people use this tank for turbo applications. This tank has the shorter neck with restrictor for lead free fuel nozzles as required by Japan and Germany and uses the thinner neck seal [link...
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
MINI Auto only. Minispares brand Paper element for canister type Automtic Mini from the original approved and designated Rover/Unipart source.Much taller than the manual type this filter has to do a lot of work and fits every mini automatic made, but...
Minispares original filter fits all single and twin point injection models
sold at nearly half the retail price.
Minispares branded filter from the original and approved Rover/Unipart supplier until 2014
Minispares brand air filter element from the original approved and designated Rover/Unipart source.This air filter originated on the Metro range but was used from 1990 on any minis fited with a HIF type SU carbs that have the integral float bowl in i...
Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014. Original filter for twin point injection cars where it screws directly into the block.
See GFE210 for shorter fil...
Genuine Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014 when parts quality selection changed.
Same manufacturer and item as GFE443 but with our livery on so you know you are g...
Short oil filter for MPI when space is restricted through modification or optional oil cooler fitted
MANN supplied Filter
this short filter DOES NOT fit the MPI block. it ONLY fits the oil cooler take off
Replacement screws and nylon inserts for the Van, Estate and Pick up petrol tanks.
The main cause of failure is water in the pump. This is caused by modern ethanol fuels. Be sure to clean the tank out before fitting and drive your mini more to avoid water build up.
Replacement pump only for the original WFX100810<...
5/16" bore petrol hose for injection cars sold in metre lengths.
Resilient to heat,weather and suitable for ethanol in modern day fuels.100psi max.R9 spec.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.