CARB BUTTERFLY HIF38 DISC KIT
WZX1387

($14.40) £14.40 exc vat

($17.28) £17.28 inc vat

In stockIn stock
Plain butterfly disc kit for the HIF38 carb,which we sometimes order in in as requested by the customer as they are very slow selling--same size butterfly on all 1.5" carbs

($14.40) £14.40 exc vat

($17.28) £17.28 inc vat

In stockIn stock

Recommended usage 1 x WZX1387 to fit one mini.
HIF38 Carburettor 38mm 1.5 inch - Qty 1
Carburettor HIF38 and HIF44 - Qty 1

Alternative products

plain butterfly with small hole at bottom for HS4 waxstat jet type carb and uses WZX177 spindle-or see kit full rebuild kit CRK121. This is usually fitted to FZX3013 replacement carb --same size butterfly on all...

People also bought products

Small hose clip for 1/4" fuel line (our part number PETROLPIPE)

Throttle disc only for HIF44-non turbo and if replacing the spindle there are 2 type, threaded one end only use WZX1127 for very early carbs 1980-81 only, but all later cars were threaded both ends use WZX1128

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.

Fitted to HIF38 and HIF44 carbs, ethanol tolerant product. Bigger bodied valve.

For turbo models see WZX1095 .Quantity required-1

Float needle valve for turbos fitted with standard HIF44 carb. Larger bodied valve.

Inlet size is 0.096". See also WZX1090 smaller bodied valve HIF6 MG Turbo

This float is ethanol tolerant and will fit all HIF38/44 carbs and the spindle is CUD2082 ..Quantity required-1 set for single carb.

Turbo uses WZX1095 needle valve. An expensive puncture proof stay up float is av...

spindle threaded both ends for HIF44 for most late carbs--see WZ1127 for spindle with thread one end only as per early metro cars. Thread size is 1/4 BSF

bearing and needle jet kit(not carb needle) for both HIF38 and HIF44.

.Quantity required for single carb-1 set.

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

Service repair kit for the HIF38 carb (1.5") fitted to the first 1275 engined cars in 1990s such as the sprite.

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

This is...

Special rubber hose 1/4" bore for use on petrol lines, this is in black and not armour plated outside but does have internal reinforcing. Supplied as pre cut 1m length with 2 clips and is safe to use with modern fuels with higher ethanol content. SAE...

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orange ...

spindle and parts only required to refurb your HIF38 carb- for butterfly see

WZX1387

Gaskets and spindle/float lid seals for all the HIF38/44 range.

For HIF38 service kit see CSK94 for mini and CSK78 for metro

for HIF44 see CSK75[/lonk] except turbo

[link]CRK167
rebui...

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

Our heavy duty throttle cable is superior in many ways.

A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.

Cable to carb bolt is ACC5062.