Original classic looking Monza non locking ALLOY cap with the mounting collar to fit tank included.See MONZA also for description
To fit the collar for this cap you will require 10mm(0.3937")just over 3/8" of petrol tank neck ac...
non genuine R/H outer MK3 door skin.
not as good a fit or looking as the genuine CZH3301 but a good inexpensive replacement less mirror holes
The last product from the factory in wheel arches (flares) are these fancy "Sportspack" arches. Factory originals are expensive but this fibreglass set will give the same look. Also see ARCH001. As with all fibreglass products, some modi...
2-3" lower section of Van body section
from A post to rear wheel arch including the vital door step sill profile that rusts plus the horizontal edge that the chrome trim sits on-for cars with hinge tye doors
non genuine oversill MK1/2 van floor profile R/H with 4 flute vents
see MS58R for 6 flute type side, wide type
pair of outer door seal mouldings and fixing clips
These are the original type without the black plastic ends which were introduced on later models for safety criteria. All outside moudings are interchangable but are sided.
Non genuine body side skin from door back and below window line for the left hand side
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
Never have a misted up front screen again. As used on Monte Carlo and other top Rally cars. 2 horizontal silver bands/element wires going across the screen a few inches from the top and 3.5 inches from bottom. Not suitable for twin point cars as the ...
Aftermarket version of the L/H floorpan for 1991 on cars.
This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...
Genuine Mini Spares mouldings product as supplied to Rover.
These fit on the inside of the door as a draft excluder for the window, on all wind up window cars from 1970 on.
Sportspack type decal kit.
This kit includes 2 mini cooper laurels and pin stripes to cover bodyside, door and front wing as a car set with the bonnet stripes in white.
When they introduced negative earth sytems for the MK3 cars they had to put these stickers on the cars to warn people as all previous models were positive earth which caused havoc with people trying to fit radios and other electrical equipment with t...
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.If you are looking for a cheaper budget version see PAM3077MS
...
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the R/H upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.
promotional sticker to advertise your favourite mini parts supplier who just happens to be the largest in the world bar none-
Holds the window regulator to the door on wind up window minis from 1970 on.
Also holds fog lamp bracket to rear valance. 1/4" unf with 1/2" thread on
panhead type screw.
promotional sticker to advertise your favourite mini parts supplier who just happens to be the largest in the world bar none-The Union Jack Heart only as per Mini Spares emblem from 2005
This windshield has a very slight tint all over, barely noticeable but enough to reduce glare and make the car cooler inside. Fits all years and models of Mini
except twin point cars which have built in mirror base. IF A MAIL ORDER OR INTER...
Moulded shape type right hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.