This twin line brake PDWA valve is fitted on the front bulkhead of the engine bay from 1978 on as opposed to the single line valve which was fitted on the rear subframe.
Fixing bolt is 2.25" long UNF 1/4. The 4 Brake unions are all metric. ...
A pair of L/H shield covers for 7.5" disc as fitted to Cooper S
The little locating bracket to the hub is available seperate as BTA1209
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
Same steel braided pipes but includes the clutch pipe for Verto type clutch.
Please be aware the fronts are sided, the deeper threaded hose fits the right hand side, the shallower hose fits the UK passenger side.
Cooper S 7.5" complete brake disc kit, except for disc shields, with genuine AP calipers and Tinken bearings. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes. See C-AJJ4028MS for kit with our ow...
Genuine AP Lockheed boxed - Made in UK - fitted from 1988 on, this master cylinder uses a built in servo.
This master cylinder was used right up to the last production twin point vehicles from Rover. Bore size is 20.6mm(.811").
See ...
From 1976 the handbrake cable layout was changed, instead of two cables from the handbrake it was changed to one. Front for the saloons is 25" long and the van requires 29.5" long which is available as FAM625. The cable between the wheel...
Made in easy bend non rust material this one will fit the regulator valve on the rear subframe to rear hose on hydrolastic cars only as it is 8" long.
These pipes are retail less 35% discount at least to keep prices viable.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI & MkII Minis up to 1976 and the throttle pedal on post 1976-1996 models.
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI to Mk3 Minis pre 1976 and on the accellerator pedal from 1976 -1996.
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
Correct size and length brake pad pin for the caliper using 7.5" disc size as fitted to Cooper S and 1275GT. 4 required for 1 car, also fits Cooper 7" calipers. 3mm diameter.
These repair kits are for the later twin leading front drum brakes wheel cylinders GWC126/7 with .9375" bore size. The earlier twin cylinder set up used part number 8G8816 for GWC102/3 with 0.8125" bore size.
Easy bend copper 24"long brake pipe with one female and one male end for the regulator on the rear subframe to the n/s/r hose on hydrolastic cars only.
Also used on split front to rear system with valve in engine compartment - from 3 way uni...
Easy bend long life copper brake pipe with 2 male ends and ideal and best replacement for the original 16" pipe from the 3 way union to the brake switch on single line dry suspension minis. These kits or pipes are at least 35% off retail.
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
A special 3/8" unf half nut (9/16"AF spanner size)for fitting on rear brake hoses and carbs to manifold.
Male metric brake union as used on front to rear PDWA valve and later master cylinders. Pipes should be double flared.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.