Minispares own product-L/H, to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Engineering but in the 90's we put down tooling with IVRA/Italy who had them manufactured by Torm...
UK made 8.4" brake disc. Priced individually but should always be replaced in pairs for safety and braking efficiency. These are the best quality available of the low priced brake discs on the market and suitable for all standard road use.Beware of t...
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
This stainles steel caliper piston fits all Minispares 4 pot calipers plus Metro and ERA turbo 4 pot calipers.
From 1989 minis which have the brake servo built into the master cylinder and it is very difficult to work in the engine bay, especialy clutch changes because of the extra room taken up by this dual cylinder. By replacing the 2 metal brake pipes from...
Special formulated hose for brake servos and engine emmission breathers sold in a 22 inch length. 3/8" inner bore.
You'd think that the way Minis leak oil they'd never rust on the undrtside, but they do! If your Mini is rusty below it is a good idea to check your metal brake lines; rust on them could be disasterous.This complete kit is available, in non-corroding...
Single line brake R/H/D pipe kit for hydrolastic cars with a servo fitted. Also includes the 2 front wheel cylinder bridge pipes for drum brake variant cars. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If ...
Used on all 4 pot alloy calipers as well as standard fitment for Metros.
A set of split pins and metal retaining clips are available as GBK1025
3.300"wide
Genuine AP Master cylinder with plastic tank.
The master cylinder is the heart of any hydraulic system and the hardest to troubleshoot. A pedal that can be slowly pushed to the floor indicates the master cylinder is worn. Fluid dripping off ...
Front to rear brake line kit for cars from 1988-2000 with the factory Servo incorporated into the brake master cylinder. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good...
Almost every Mini built prior to the dual circuit system uses a .70" bore master cylinder. This kit fits them all. The original size in the '59-'64 Mini was .75" but as most of these cylinders have been replaced with the .70" size it is best to check...
Easy bend copper brake pipe 26" long with one female and one male end - used on hydrolastic cars from regulator valve to near side rear hose. These pipes are retail less 35% discount at least to keep prices viable.
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Pair of 4-pot alloy calipers for 8.4" diameter brake discs with 12" (or bigger) wheels. Kit includes pad pins, but not brake pads.
The advantage of alloy calipers is that they dissipate heat quicker, reducing fluid boiling. The design a...
Non genuine pair of L/H disc shield covers for the 8.4" disc size. Fitted as standard from 1984 to 2000. Non genuine but all that is available. It comes complete with the little locating bracket. If you require just the bracket, order it separately ...
PRICED INDIVIDUALLY per disc but should always be fittted in pairs for safety and efficiency..
THERE IS AN ALTERNATIVE GROOVED AND DRILLED PAIR OF DISCS SOLD AS C-GBD496.
Set of alternative pads for use with 7.5" wide discs.
From Mintex the developers and manufacturers of mini braking systems as per GBP103AF from Xpart now.
Single line kit L/H/D when no servo. This kit contains all the pre-made lines required to replace all the brake lines on a left hand drive Hydrolastic Mini. The copper tubing is easy to shape and will never rust!-includes 2 bridge pipes for front whe...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.