13" long pipe has one metric male end and one unf male union.
IF connector piece BMK2466A is fitted the pipe would originally have been 11" long, but this pipe by virtue of being easy bend can be used without the connector. Also...
Twin leading shoe brakes use two wheel cylinders per wheel, but you buy them singly. These cylinders are the 15/16" (.9375") diameter style that will fit MK1/2/3 models 1964 on with 1 1/2" shoes.
Sold with bleed nipple but require[link]37H38...
copper easy bend brake pipe with 2 metric male unions. 14" long
These pipes are retail less 35% discount at least to keep prices viable. goes from the top union on the master cylinder to the right union on the valve (to feed the front brakes...
Genuine AP car set of 4 brake hose for cars with front disc brakes. If you are changing one through wear and tear it is a good idea to change the whole set and save money with peace of mind about your brake system. Securing nuts included
This master cylinder had a larger capacity fluid bowl 3" high and was fitted to all cooper S and 1275GT with single line brakes. Will also fit standard single line mini if you are looking for larger capacity fluid reservoir especially when using cali...
Servo repair Kit for all models after 1989/90 where the servo is buit into the master cylinder. The gaiter for the brake pedal is NAM8567
Special plastic covered clevis pin(first one to appear on a mini) is for the later brake system with servo and intoduced on single point injection.
Sleeve nut connector for metric type male unions. Fitted to cars Pre Servo before 1988, to allow engine subframe assembly to be installed on the assembly line, and then connected to PDWA valve as brake lines already fitted on shell. When the servo wa...
Rear Braided brake hose set, with banjo union bolts and howver you need some tie wraps to hold hose to arms, runs from Radius Arm to Rear Cylinder, replaces both standard metal and rubber hose. No modifications are required and is of special interest...
IF YOU HAVE A VERY OLD .75" BORE MASTER CYLINDER THIS IS THE REPAIR KIT.THIS FITS MASTER CYLINDER GMC153 WHICH IS AVAILABLE FROM MINI SPARES
Rear wheel cylinder with 0.6875" bore size first appeared in 1974 on single line 1275GT cars and then on some split diagonal until 1976--also fitted to Innocenti cars when they had a unique 4 way swith union--- repair kits for these cylinders are [li...
10" long pipe with 2 male ends used on front drum brakes to join the wheel cylinders. Made in easy bend copper for long life. These kits or pipes are at least 35% off retail.
see 21A1206 for pre bent steel rh
Original kit for front to rear metric brake line system with green or black band master cylinders 1980-1984, but now also includes a pipe with lower 12mm union for GMC227 current yellow band master cylinder without servo as fitted to 198...
The four tension springs as a car set for the rear drum brake shoes which should be replaced at least every other shoe change under normal circumstances.
This kit also fits front brakes with 1 cylinders per drum from 1959-64
Single line brake pipe kit for dry suspension cars without servo pipes but including the 2 front wheel cylinder bridge pipes for drum brakes. If you have a servo you should use GB4992 (does not have bridge pipes for front drum brakes).
Saloon 1974-76 approx diagonal split system with PDWA valve which had unique 7/16" size unions on valve--for van/estate use GB4996-Split diagonal with 4 way valve--4 way valve only fitted to R/H/D Japan market.
You'd think that the way Min...
Diagonal split brakes with metric master cylinder 1977-82 approx.Saloon.
The kit now has longer pipes from the 3 way to the rear hose which cuts out the bridging unions and odd metric end pipe that was only fitted to help assembly line fitti...
When master cylinder had all imperial size unions and no servo. R/H/D front to rear system, Saloon 1978-80 with original green band master cylinder.
For black band master cylinder with metric unions see GB4999.
You'd th...
If you have original drum brakes on the front of your mini with twin leading shoes (2 cylinders per drum) this is the kit of 4 tension springs you should change. Originally a double spring type they are now single spring coil per item but more effici...
Twin leading shoe brakes use two wheel cylinders per wheel, but you buy them singly. These cylinders are the 15/16" diameter style that will fit MK1/2/3 models 1964 on with .9375" bore size with 1 1/2" shoes.
Sold with bleed nipple but requi...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.