NUT PLAIN 1/4" UNF
GFK3211

£0.07 exc vat

£0.08 inc vat

In stockIn stock

£0.07 exc vat

£0.08 inc vat

In stockIn stock

Recommended usage 1 x GFK3211 to fit one mini.
997CC & 998CC Cooper Cylinder Head - Qty 2
Cylinder Head, 998CC, 'A' Plus 1980 on - Qty 2
Clutch Housing - Qty 1
Front Hydrolastic Displacer Suspension ( Known as - Qty 2
Steering Columns, Locks & Cowlings - Qty 1
Emission, Carburettor Fittings and engine controls - Qty 1
Flywheel and Clutch - Qty 1
Gearbox Transmission Case - Qty 3
Heating and fresh air ducts/hoses - Qty 1
Steering Wheels, Locks and Columns - Qty 1
Rear Brakes, Handbrake and Mechanism - Qty 1
Brake Pipes - Front to Rear Split 1985 on - Qty 1
Speedo cable and fittings, clock and gauges - Qty A/R
Bootlid - Qty 8
Bumpers and Number Plates - Qty 6
Carburettor Fixings, Throttle Pedal & Abutment Br - Qty 1
Front Rubber Cone Spring Suspension ( Known as Dr - Qty 1
Front Suspension - Qty 2
Front Door - Sliding window type - Qty 4
Battery fittings, cables and main looms - Qty 2

Recommended products
Alternative products
Kit products

Genuine Mini Spares product-of which, some parts were supplied to Rover.

Stainless steel automotive grade unlike the poor looking chrome set up imported by some and sold cheaply. The "Deluxe" models of all Minis included bumpers with these ...

This fitting kit suits all later day 1.25" and 1.5" twin carb set ups where the balance rods between the carbs required are equal length (2.25"), some early carbs had the balance bar with a triangular plate that were a shorter length. The kit has the...

This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...

This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...

Not Built up= A Complete kit of HS4 CARBS/ MANIFOLD/LINKAGE LESS AIR CLEANER

This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the abutment bracket on the inlet m...

Quick Release Bonnet Hinges , MK3.one pair

Available for MK3 onwards Minis only. The MK3 Mini has hinges mounted differently from earlier models, these allow the bonnet to be quickly lifted off the car. If you've ever banged your head or cri...

This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...

Not built up-A matching pair of HS2 twin carbs with polished dashpot covers and stainless steel heatshields plus original type twin HS2 linkage kit, inlet manifold but less air cleaners etc.

The UNC bolt holding the...

Complete nut, bolt and washer set for engine to gearbox only

Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:

Inlet/Exhaust manifold to head, studs/nuts/washers

Thermostat housing (no sandwich plate) studs/nuts/washers

H...

Complete fitting kit for the door check straps on all Minis fitted with external hinges.

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

This kit includes all hardware to fit suspension to your front subframe. Also includes front damper mounting hardware and lower arm pins.

Boot hinge gaskets and fittings for original type hinges

People also bought products

Boot hinge gaskets and fittings for original type hinges

This kit includes all hardware to fit suspension to your front subframe. Also includes front damper mounting hardware and lower arm pins.

8 slot castle nut for disc brake CV joints. The extra slots make it easier to reach the factory torque setting.

Engine mount bolt kit for manual cars, 1 kit requried per car.

5/16" UNF cage nut as fitted to CZH3241 tank bracket on cars fitted with a 7.5 Gallon fuel tank. Uses 13H7583 bolt

Wiper mounting kit for Mk1 Mini's (3 required per car). Each kit comes with a pin, nut, 2 washers and mounting rubber.

5/16" UNF A2 Stainless Steel Plain nut, ideal for engine bay dress ups or nuts that you don't want going rusty!

A2 Stainless Steel 5/16" UNF Nyloc nut, ideal for engine bay dress ups or nuts that you don't want going rusty!

M6 metric lock nut -fits 14A6779ms bumper

Metric M6 PLAIN NUT.sold singly per item

Required for non genuine stainless steel and chrome bumpers.

Fits radiators with metric fittings such as ARP1110

METRIC FLANGED NUT AS USED ON ENGINE ANCILLARIES FROM 1990 ON

Metric flanged metric M6 nut as used on engine, air con units and heaters from 1990 on.

METRIC M8 nut for holding bolt on spotlamp brackets on SPI/MPI plus other parts

Plain half thickness half inch nut as used on our C-AJJ3365 arms and steering rack adjustment nut for track rod ends.

Wing nut to secure the air filter box on Cooper & Cooper 'S' models.

New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...

Original metric fixing nut for genuine Rover sportspack arches.

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.