(¥30) £30.08 exc vat
(¥36) £36.10 inc vat
In stock
(¥30) £30.08 exc vat
(¥36) £36.10 inc vat
In stockRecommended usage 1 x HAM2457FKL to fit one mini.
The battery cover made of a special cardboard as fitted to all minis to protect
the battery terminals from metal objects. See also the 14A7666 retaining strap.
They increased the length on this hook end bolt by 2cm in 1990. The shorter version @5.5cm is 5L1159 -this fits the front
Battery rod with loop for cars with larger battery 8.55mm long.
Also see 5L1158 shorter version at 6cm long for Pre 1990 cars.
This item for post 1990 cars is the looped battery fixing rod with longer thread that fits o...
Fixes fan blade to water pump and corner bars to overider on deluxe bumpers. Also used for locating plate AHU2379.
Your battery box 5L877 should be held in place by this rubber strap.
Battery strap metal clip that is bolted to boot floor, now in stainless steel to help stop corrosion. Later cars had a captive nut in the boot floor, if you have an early car or the nut has corroded use GFK3212SS to secure the bolt.
Stainless steel small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.
Small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.
universal battery clamp replacement with securing bolts and marked N
Your battery box 5L877 should be held in place by this rubber strap.
Universal post type battery earth strap with clamp type fitting and correct length for most alternatives of batteries fitted.
Universal battery clamp replacement with securing bolts and marked P.
They increased the length on this hook end bolt by 2cm in 1990. The shorter version @5.5cm is 5L1159 -this fits the front
Battery rod with open loop.
At 5.5cm long this is the open loop rod by the negative terminal which hooks into the battery box bracket. Also see YJJ100040 at 7.5cm lomg made ffor 1990 on cars with bigger battery.
Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.
ECU for mini automatic---Japan spec SPI from 1996 on----
Resistor for AFU3389LED and AFU3389WLED, this is needed to enable the lamps to function properly. Sold in pairs.
This is the bracket that bolts to the front of the mpi blocks to hold the more modern type coil pack. The original type is no longer available so we had this made in stainless steel.
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Plastic holder for the later flasher unit GFU2218. Needs to be mounted to the bulkhead prior to fitting the flasher unit to the holder
INDICATOR LAMP WITH ORANGE LENS AND LED BULBS. Sold singly, 2 required per car
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
1.0 KW steel gear reduced unit, that draws less current from the battery when starting. Huge increase in comparison to the original units, and are a direct replacement part for the original pre-engaged starter motor.
Not ...
Courtesy switch for MPI minis from 1996 when the wiring was changed from bullet type to spade connection. This is the switch that fitted into the A post to turn the interior light on and off, the earlier switch is no longer available so if you have a...
Rear body harness with speaker wires,known as thin wall PVC type type which replaced the thick wall type in 1989. AN166 is the thick wall early equivalent.
If your car has no speakers just disregard the extra wires. This loom ha...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.