LAYSHAFT 4 SYNCHRO single step PRE A PLUS
22G931

£20.21 exc vat

£24.25 inc vat

In stockIn stock
For the pre A plus gearboxes and unlike A Plus do not have a step in them where the bearings sit. It does however have one end larger than the other. The bearing part numbers are 88G396 and larger CHM141

£20.21 exc vat

£24.25 inc vat

In stockIn stock

Recommended usage 1 x 22G931 to fit one mini.
4 Synchro Gears Up to 1979 with 14MM Nose Mainsha - Qty 1

Alternative products

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...

Kit products

Full rebuild kit less differential parts, supplied with standard layshaft

Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use.

This...

Full rebuild kit with dihferential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

People also bought products

High quality version of 13H9513, INA branded.



Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.



Kno...

Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.

For all rod change gearbox mechanism housings, this as un uprated poly bush replacement for the standard rubber bonded mount

Kit which enables you to fit a rod change gearbox to an earlier round tunnel.

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...

Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...

Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips

NLA see 22G2022MS:Used: (secondhand) 5 tooth drive spindle mainly used on Metro range but includes ERA turbo mini with 3.2 final drive using 16 tooth plastic pinion.

Obsolete new but offered "used" in case a ratio change is required. The on...

Short diff housing bolt fitted to Rod change gearbox only 3/8"unc and 2.25"long. For the 2 long STUDS useTAM1617.

For use on Diff housing

Remote type case

53K266 are 4.5" long -4 for remote now use

Short diff housing bolt fitted to Rod change gearbox only 3/8"unc and 3"long. For the 2 long bolts useTAM1617. UNC course thread for case end and UNF for the nuts. All sold singly per item

53K266 are 4.5" long -4 f...

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)

housing and deleted 1996 on.locking glue used such as locktite

Oil seal for speedo drive pinion cover (DAM8488)

New Minispares Evolution straight cut crownwheel and pinion set 3.875. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x62 teeth count

Always Check...

Full rebuild kit with dihferential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit less differential parts, supplied with standard layshaft

Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use.

This...

Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...