($20.10) £20.10 exc vat
($24.12) £24.12 inc vat
In stock
($20.10) £20.10 exc vat
($24.12) £24.12 inc vat
In stockRecommended usage 1 x DP3 to fit one mini.
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...
Hardy Spicer Adapters to convert pot joint output shafts to fit a hardy spice coupling (will also fit the Quaife ATB)
UK made straight cut PRE A PLUS gear kit includes 1st, 2nd, 3rd gear, 1st motion shaft, reverse gear and laygear for remote change. Please order genuine C-22A1741 or 22G2033EVO baulk rings when fitting this gear kit. These are the original ratio and ...
USED old and slightly rusty but usable-This is the later differential cast type cage which takes the planet gear thrusts DAM5071 that have a lip on as per all later A plus gearboxes.Other than the recesses to accept the later thrust wash...
USED 3rd gear has 2 identification grooves on the 20 main teeth and was found on 1275cc Metro and Mini SPI{12G04/JO5/J92 engine numbers}{
USED ITEM
For all rod change gearbox mechanism housings, this as un uprated poly bush replacement for the standard rubber bonded mount
Kit which enables you to fit a rod change gearbox to an earlier round tunnel.
Competition crownwheel bolt for use with our LSD crownwheels, these are CNC machined from EN24T with a reduced head height for more gearbox clearance.
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Full rebuild kit less diferential parts with competition layshaft and EVO baulk rings.
Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. <...
Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.
These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
This unit fits directly on to the gearbox in place of the standard cable and produces a digital signal for use with an electronic speedometer requiring a 5 volt square wave pulse such as our electronic speedo 13H4443. For pre 1980 speedo...
Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS
Using only the original manufacturers of the bearings such as RHP because all t...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
USED laygears--For the late model Mini A Plus gearbox,with single groove identification, this standard ratio laygear was used throughout the range until MPI! No longer available new but we have available good used items in stock where we replace with...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.