RAD CAP '92-'96 FOR RADIATORS WITH SENSOR SWITCH,1...
GRC207

($6.13) £6.13 exc vat

($7.36) £7.36 inc vat

In stockIn stock
Any original side fitting radiator with the sender unit in the bottom on SPI 1275cc models from 1991 on. This 15lb radiator cap has a top rubber seal on it to ensure an air tight fit creating a vacuum as these models were fitted with an overflow bott...

($6.13) £6.13 exc vat

($7.36) £7.36 inc vat

In stockIn stock

Recommended usage 1 x GRC207 to fit one mini.
Radiator & Fittings - Qty 1
Radiators pre 1996 - Qty 1

Recommended products

Sensor type Radiator that uses the original Rover clip in type sensor hole in the bottom which was fitted from 1991 up until the introduction of the twin point front mounted type.

This is a Cuprobraze 3 tube modern design version with 9 gill...

Alternative products

Fitted from A plus on to increase engine running temperature. If your radiator has a sender unit in the bottom you may have an expansion tank and therefore the radiator will need a better sealing pressure cap which allows a small vacuumGRC20...

People also bought products

Alloy lightweight original looking radiator with correct shape header and lower tanks, same as ARP2000 to look at but made in alloy with latest technology cuprobraze manufacture. 6 Metric fixings screws required if you have old imperial ...

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

Mini air conditioning compressor, as fitted to any model of Mini with air conditioning as a factory option including Japanese spec cars up to chassis number 134454.

Oil cooler union for later cars, will fit the oil filter head and block, 1/2" BSP to 11/16". Requires DSM18 to seal. These are handy when you have changed to a later filter head etc and want to fit an early oil cooler kit.

Silicone hose kit for 998 vehicles from 1989 onwards that were equipped with the plastic inline heater valve, comes complete with moulded heater take off pipe and 5/8 heater pipe.

Heater hose that comes from the cylinder head take off to the plastic inline heater valve on 998s 1988 on - this can also be used with a heater take off on 1275cc engines.

Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.

MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...

3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impeller...

3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.

Fitted with a PPS, glass filled plastic impe...

Spring clip for securing the top hose on MPI front mounted radiator models.

This is the metric nut needed for PQR10028 tensioner as fitted to all mpi mini's.

m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)

original imperial radiator screws were SH604031 or PK type were ARA1117

Oil cooler kit for MPI models. Oil cooler is 10 rows, 21cm long and 9cm high. Unions are 18mm and require the special fitments as supplied in this kit. The oil filter is GFE210

Universal aluminium heater assembly complete with heater matrix and electric fan. Comes with 2 outlets for demisting windscreen and 2 variable vents for heating the rest of the car. Ideal for track/race cars or simply for those who want to replace th...

Silicone heater hose, 39" for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1988 cars.

Silicone heater hose, 39")1metre) for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.

Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does

Designed to reduce the horsepower drain and slow down the water moving through the radiator to allow it time to cool, its very important for the higher RPMs we run today. This oversize pulley is 4.2" diameter, earlier cars used a 3.875" wide pulley. ...