Showing 481 to 500 of 1205

Seal for door handles MK1/2 and all sliding window exterior hinge cars.

also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate



is oval shaped



for boot / rear door use the hole at the rear ...

Plastic window locks for sliding windows, metal ones are no longer available.

24A1194 = Right Front

24A1195 = Left Front

24A1196 = Right Rear

24A1197 = Left Rear

For mini's with sliding windows on the front doors, these are the runners that hold the channel and have holes to lock the window catches. Now made in stainless steel by Minispares to ease rust problems.

Also see 24A1303 for R/...

If your MKI or MKII suffers from terminal "door handle sag" it is quite possible that the inside door latch mechanisms are tired. A left hand drive car should have a locking latch on the right side (the driver's side key-locks with the handle). Right...

It is possible and almost easy to repair sagging Mkl Mini door hinges . You don't even have to remove the hinges from the car. Once you have removed the original hinge pin you simply drill a hole in the front hinge half, push in the bush and reassemb...

Four tailor made felt pieces to fit in the segments between the bonnet strengthening webs to allow maximum under bonnet clearance.

See FELT860 for spray adhesive. These are about 1cm thick and the original very thick sound dea...

Inner front R/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment. Always check the bonnet prop bracket location as they changed.

Inner l/h wing with large fan hole from 1991-96. This panel is available with the A panel fitted for ease of fitment as ABD36005

Was ABD36009 but that did not have the stiffener plate for the damper bracket fitted which was diff...

Lower moulding clip for wind up window mouldings..4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5

Also used for 24A1169 glove box moulding MK1/2.

Genuine rear luggage pocket but the later shape without ash trays but a mounting recess point for inertia seat belt, this is the nearside l/h.

Genuine Mini Spares quality product. For Mk1 cars use 14A8744

For Pickups you will need to cut and shorten either seal and make sure the join is at the bottom. The extrusion is the correct shape.

This seal is the best ...

In nimbus if you want to keep the car as original.

This is the bracket on the inner wing to put your bonnet prop into when the bonnet is in the open position.

The MKI Mini door is distinctive with its external door hinges and inside pocket and sliding windows. The single biggest problem with the doors is the tendency to rust particularly along the bottom edge. Make sure you replace the drain pipe rubber h...

Minispares made.These are for R/H/D only cars with 1mm thicker and 2mm wider stainless steel arms, plus a stronger spring to keep your blades firmly pushed on the screen when motorway driving or at speed.





Some Minis have...

The MKI & MKII number plate panels 14A6468 are hinged at the top to swing out clear of the bumper when you open the boot lid. They were unavailable for years but now they're back. If you also need the hinges they are 14A6466...

Hinge for any mini with external hinges and uses gaskets BMP135 on A panel and and ALA7844 on door. Supplied with new studs/nuts and washers for fitment but if you need spares see 14A6818BOLT new set of bolts an...

Some bumpers have studs, some require bolts, this is the bolt.

These special hoses are for all sliding window type doors to drain the water away from the channels. The thin end of the hose slides into the bottom tube to ensure water goes out and cannot leak into the bottom of the door and the top slides over the...

Genuine front panel fits all pre rubber mounted subframe cars .

The early pre 1964 Mk1 had different shape lower valance without cut aways under the bumper apron but this genuine panel will fit all.

There is a good aftermaket panel...