Use C-AHT223GREEN as these original cooper pads seem to be obsolete and if you have the very early small pad type as per 997cc Cooper, get the calipers machined out to accept this pad as the small type GBP101 or BD20 is now ...
For those old original drum brakes on the front of a mini with 1.5" wide type fitted. Some pre 1964 dry suspension had the smaller rear type 1.25" wide fitted the same as the rear. After Unipart's demise our stock from Oct 1st will be Mintex as used ...
Minispares own brand upgraded to GR260-BS1452.
This is 7.5" diameter disc to fit all Mini Cooper S and early 1275GT models and is ideal for all fast road uses. For standard spec material see GBD101MS.
Easy bend copper-nichel brake pipe kit for L/H/D front to rear split system,also with pipes for drum brakes for pre 84 cars. the m/cyl pipes are longer and only for GMC227 with 12mm lower union--if older type B/M/cylinder a 10mm both end...
HYDROLASTIC WITH SERVO and includes 2 front wheel cylinder bridge pipes if required. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good idea to check your metal brake line...
Brake hose kit to convert Metro calipers to fit single line mini systems. This kit contains two short braided link pipes, two long braided hoses, two banjo bolts and the copper sealing washers.
Plates for protecting the brake hose to the front calipers as used on works cars. Sold as a pair.
The 7" diameter original Mini Cooper size disc. This was standard fitement on all 997/998cc Cooper models 1961-69. (NOT suitable for Mini Cooper S which use a 7.5" diameter disc).
Genuine AP product as original.This strange looking coily spring holds the front brake shoes against the drum for better braking efficiency by holding them in a set position which also cuts out brake judder caused by sideways movement.
Fitte...
Genuine AP L/H caliper-Whether you are upgrading from the smaller 997/998 discs to the larger 'S' brakes or simply restoring a Cooper S, you'll appreciate the value of these brand new brake calipers. See 27H4657MS for our own product.
Cooper S disc brake water shields are easily damaged and hence frequently missing altogether. A complete kit consists of six different components: upper and lower shields plus mounting tabs for each side. Complete set is 21A1271, [link]2...
special double coil spring washer which fits on the rear hanbrake quadrant on Hydrolastic cars only.Known as a thackery washer
12" wheel to 10" wheel running gear conversion kit. Less wheels
this kit will convert your 8.4 disc set up to the original Cooper S 7.5 discs to allow fitment of 10" wheels, kit includes discs, calipers, pads with split pins and drive flange...
Non genuine pair of R/H disc shield covers for the 8.4" disc size fitted as standard from 1984 to 2000. Non genuine but all that is available, it comes complete with the little locating bracket. If you require just the bracket order it separately as...
Non genuine -All later models have these 3/4" bore double piston cylinders for the rear brakes.INCLUDES BLEED NIPPLE AND CLIP. The gasket 37H4642 is not supplied but these non genuine type have proven very reliable. Repair kit is [link]G...
Copper easy bend 10" long metal pipe with male and female end fittings to fit between rear wheel cylinder and flexible hose on dry suspension models. These pipes are retail less 35% discount at least to keep prices viable.
Mini Spares standard road use disc 7.5" wide using material GG25EURO.
These were standard fitment on all Cooper S models plus early 1275GT made from OE drawings to the correct material spec. Cheaper types on the market that we have tried sin...
Set of 4 Brake pads from the original manufacturer Delphi for the 8.4" wide disc fitted as standard to minis from 1984on with 2.920" pad width.
A set of split pins are available as GBK1010 or with metal retaining clips as [link]...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.