(3,00 €) £3.00 exc vat
(3,60 €) £3.60 inc vat
In stock
(3,00 €) £3.00 exc vat
(3,60 €) £3.60 inc vat
In stockRecommended usage 1 x 22A285 to fit one mini.
High quality version of 13H9513, INA branded.
Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.
Kno...
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...
USED old and slightly rusty but usable-This is the later differential cast type cage which takes the planet gear thrusts DAM5071 that have a lip on as per all later A plus gearboxes.Other than the recesses to accept the later thrust wash...
Change speed lever on gear change shaft for remote and magic wand type gearboxes
stamped 2A3358 and MOWOG on back
Kit which enables you to fit a rod change gearbox to an earlier round tunnel.
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.
These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
NLA see 22G2022MS:Used: (secondhand) 5 tooth drive spindle mainly used on Metro range but includes ERA turbo mini with 3.2 final drive using 16 tooth plastic pinion.
Obsolete new but offered "used" in case a ratio change is required. The on...
Short diff housing bolt fitted to Rod change gearbox only 3/8"unc and 2.25"long. For the 2 long STUDS useTAM1617. (0,34 €) £0.34 exc vat (0,41 €) £0.41 inc vat
For use on Diff housing
Remote type case
53K266 are 4.5" long -4 for remote now use
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
