vandervell bearings 1.64" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at 40 thou oversize. Early 850 mains were VP592 and 1.185" 30.10mm wide
Owing to non-availability of other good quality 998cc pistons, these Mini Spares Evolution design pistons from a renowned high-performance piston manufacturer are flat top with drilled oil drain-back holes rather than slots behind the rings for maxim...
This rebore size has not been about for many years but is a favourite with motorsport participants looking for extra power. Now required by customers to get that last bore size out of their blocks.
Owing to non-availability of other good qua...
Made in a hyper eutectic alloy with a high silicon content to provide tight cylinder clearances and quiet running characteristics, manufactured by a world class piston manufacturers specification" uses an optimised crown and dish (9cc) shape for impr...
later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable
3/8"unc 1"long
Owing to non-availability of other good quality 998cc pistons, these Mini Spares Evolution design pistons from a renowned high-performance piston manufacturer are flat top with drilled oil drain-back holes rather than slots behind the rings for maxim...
Mineral oil especially formulated for the combined engine and gearbox such as the mini, but for better gearchange etc use MILERS002 except on rebuilt engines where pistons must be allowed to bed in using non synthetic oil. 5 litre bottle.
Se...
ESPECIALLY FOR MINIS
This 20-50w semi synthetic oil is produced especially for minis where it needs to lubricate both engine and gearbox parts giving the neccessary coating and protection. Semi synthetic has a long life to 100c with maximum ...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Owing to non-availability of other good quality 998cc pistons, these Mini Spares Evolution design pistons from a renowned high-performance piston manufacturer are flat top with drilled oil drain-back holes rather than slots behind the rings for maxim...
INNER BOSS FOR CAM GEAR ON ROTO-SLDE BELT DRIVE KIT-PART OF C-AJJ3326/3326RACE
This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1249" thick. Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most standard ...
Dowel for the main cap on small bore engines, large bore engines use 12G1268.
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...
Price per rod-850/998/1098cc larger 6.35mm diameter. One piece rod which are sold per single rod and 8 required per engine.
The larger diameter improves push rod rigidity as much as possible
without having to modify the block/head ...
Extra length of 0.220" for 8 port Arden heads on 1275cc. Larger 6.35mm diameter 3 piece push rod (2 ends and 1 rod) which needs loctiting for safety although once fitted the parts cannot displace.
The larger diameter improves push rod rigi...
Duckhams Classic Q 20W-50, true to its history as “the engine’s choice” and recommended in a wide range of original owners’ handbooks, is the classic SAE 20W50 green engine oil.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.