Long lasting silicon by pass hose between cylinder head and water pump.
These are easy to cut and slide on easier than the old conventional rubber type.
It has been made this length to fit 1275cc engine,which used the longest hose.<...
5/8" straight connector piece for heater hose modifications on late minis.
Useful when re-routing hoses or joing hoses.
Mini air conditioning compressor, as fitted to any model of Mini with air conditioning as a factory option including Japanese spec cars from chassis number 134455.
Heater to in line heater valve -this hose is 8" to short bend-long part is about 14.5" and the short bend is 2.25" long. 25"total length if using GRH905. £26.99 exc vat £32.39 inc vat
Used with BAU5043 heater and 5/8"hose pre1991. This hose fits
Heater hose 5/8" bore with right angled bend and smaller right angled bend for fitting heater. longest part is 20" and then 16" from right angle --then 2" to heater. This is used on cars with BAU5043 heater matrix which exits on right ha...
5/8" Bore heater hose from heater to bottom hose on 1275cc HIF38 carb cars and SPI or any car where the heater outlets are on the left hand side 1991-1996 only. About 15" long this hose is specially shaped to help fitting but no longer available from...
Genuine Rover T shape special hose for injection cars only, from thermostat to inlet manifold and heater valve--mostly found on cars destined for export//probably Japan spec originally, it is similar shape to PCH10532.
Rover have changed the...
This 5/8 bore hose is supplied as just a straight 45MM (18") piece of hose so we recommend you purchase a length of GRH905 hose sold by the metre.
Use GRH905 hose as this is only 5/8"Hose 7" long that goes between the heater valve and thermostat on cars fitted with HIF38 carb and 1275cc engines from 1992 on
Flexible turbo air filter pipe, 60mm diameter with an internal bronze coated steel spiral spring to ensure it maintains diameter. Also used for ducting.
Available in red only.
Expansion tank for 1996 on cars with front mounted radiator. This is made in aluminium as the original is liable to break. The original threaded type plastic cap that would allow water to escape cannot be used, so a new rad cap is included. An overfl...
Heater Matrix take off fixing kit, cars only-fits on heater matrix to take the 2 heater pipes on L/H side of car.
kit includes 2 brass take off pipes with 2 stainless steel bases and 2 water seals.
The outlet pipes are made in brass...
Radiator hose kit for all pre 1989 1275GT Clubman Minis where the top hose is slightly longer. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney blue Silicone that should last forever and not degrade with heat, ti...
Resistor fitted on side of heater for the twin speed blower.
Genuine Mini Spares heater valve. The original RANCO tooling has been scrappped so beware of some imports available where the inners quickly explode loosing the metal cap and all your water when operated.This has M4 metric thread bolt included for th...
2 per engine-Longer lasting poly type radiator grommet in Yellow for 1974 on.
These were first used on the one piece cowling from 1974 on. These fit on the lower retaining bolt and 2 are required but sold singly.
Bracket for holding expansion tank on MPI cars, nla from Rover so we now make them ourselves, cheaper too! Replace your rusty bracket and check the tank for leaks which cause the rust.
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
