£0.09 exc vat
£0.11 inc vat
In stock
£0.09 exc vat
£0.11 inc vat
In stockRecommended usage 1 x GFK3212 to fit one mini.
5/16" UNF A2 Stainless Steel Plain nut, ideal for engine bay dress ups or nuts that you don't want going rusty!
Want to add a right-hand tank to your one-tank Mini? This kit includes everything, except the tank, to do it. Included are retaining straps, support brackets that mount to the rear seat back and boot floor, between tank metal fuel line and braided fu...
Exhaust mounting kit includes the 2 hanging brackets and 2 rubber mountings, new improved cast manifold clamp and fixing nut/bolts for installing an original standard 850/998cc saloon exhaust. To mount an RC40 exhaust system see RC40FK.
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
Amal carburettor kit for the Arden 8-Port head. Complete with carbs, manifolds and linkage.
Not Built up= A Complete kit of HS4 CARBS/ MANIFOLD/LINKAGE LESS AIR CLEANER
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:
Inlet/Exhaust manifold to head, studs/nuts/washers
Thermostat housing (no sandwich plate) studs/nuts/washers
H...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
Front subframe fitting kit for pre 76 twin bolt subframes, locktabs are included but not the subframe tower spacers as these rarely need changing.
Kit which enables you to fit a rod change gearbox to an earlier round tunnel.
Engine mount bolt kit for manual cars, 1 kit requried per car.
To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.
This kit includes all hardware to fit suspension to your front subframe. Also includes front damper mounting hardware and lower arm pins.
8 slot castle nut for disc brake CV joints. The extra slots make it easier to reach the factory torque setting.
Engine mount bolt kit for manual cars, 1 kit requried per car.
Wiper mounting kit for Mk1 Mini's (3 required per car). Each kit comes with a pin, nut, 2 washers and mounting rubber.
5/16" UNF A2 Stainless Steel Plain nut, ideal for engine bay dress ups or nuts that you don't want going rusty!
A2 Stainless Steel 5/16" UNF Nyloc nut, ideal for engine bay dress ups or nuts that you don't want going rusty!
Metric M6 PLAIN NUT.sold singly per item
Required for non genuine stainless steel and chrome bumpers.
Fits radiators with metric fittings such as ARP1110
Metric flanged metric M6 nut as used on engine, air con units and heaters from 1990 on.
METRIC M8 nut for holding bolt on spotlamp brackets on SPI/MPI plus other parts
Plain half thickness half inch nut as used on our C-AJJ3365 arms and steering rack adjustment nut for track rod ends.
Wing nut to secure the air filter box on Cooper & Cooper 'S' models.
New set of metric studs, bolts, nuts and washers as supplied with the alloy external hinge kit (PEASE NOTE: This kit is NOT suitable for the original hinges). The studs have allen key socket ends to help put them into the hinge easily without damage,...
Original metric fixing nut for genuine Rover sportspack arches.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.