For 850, 998, 1100 cylinder heads where there is no sandwich plate under the thermostat housing.
Fits from the thermostat housing and end manifold stud. The other end bolts to the bulkhead where the heater hoses go through the body.
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead, le...
Oil pressure relief valve ball and spring kit. Cooper S upto 1971. Can be retro fitted to all minis to boost oil pressure.
The common practice for inspecting pushrods is to roll them over a flat surface and then use the truest 8 out of a used pile! The pushrod is an important part of the valve train and must be in perfect condition for quiet running and optimum performan...
Gasket for all spin on filter heads to block except aftermarket billet types which use 88G402. For the latest state of the art gasket material see GUG705553GM
This bracket is fitted to the top engine stabiliser arm on the engine end to help retain the bushes and arm.
Automatic Minis have different engine mountings and this is the L/H which fits under the radiator side. The R/H is 22A917.
3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).
Forged EN40B steel Race crank for the 1300 solid wall block with the main width of 1.211" but has 1.625" big end journals sizes as per the original Cooper S.
All cranks have been re drawn to benefit from latest technology by having the lar...
Genuine Mini Spares primary gear for A plus 998 engines with 29 teeth-
Now with Mini Spares easy change front floating bush held in by circlip from March 2016 to save any future costs. Bush used is C-AEA3239.
Bush running ...
This A type block 3/8" unc
stud to retain the cylinder head is 11/16"(17.3mm) longer than the standard 4" type with 1.5" of thread to hold brackets for other ancillaries such as coil. Usually fitted only at the heater tap end of the cylinde...
Forged EN40B crank, 1.75" 1300 big end journal for 1300 block with stronger keyway fitted for timing gears. Forged EN40B steel nitrided Race cranks are considered the ultimate in specification, even over the "billet" type. This is mainly because the ...
A low oil pressure warning light switch is available to help protect the engine. The standard one comes on at 7lb-much too late to avoid damage. This one comes on at 20lb and is adjustable up to 120lb. Please note this is now a twin terminal switch, ...
This latest type washer with internal seal is used on the oil feed pipe from the block to the filter. One either side of the pipe union. Found on engines from about 1985 on. Sold singly, 2 per car required.
These are suitable for press fit gudgeon pin late type 998 con rods.
sold individually with rings and pin complete
Ringsets are available as R43240-20
Lower Stabilizer Kit, LH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In standard form the engine control is left to the upper stabilizer. This often result...
These con rod bolt and nut set are made by ARP in the USA and considered the best available FITS 1300 con rods plus MGB late 18V engine numbers with 11-32" bolts. Quantity required one kit per car. torque up to 38-40lb ft.
Turbo oil pump, highest flow available. 9 Gallons per minute as against approx 6 GPM. This pump is a late model slot drive and will fit into any 1275cc engine and exactly the same as the second generation of pump as sold by Unipart/Rover.
Ga...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.