Lightweight alloy Dynamo/Alternator pulley 75mm wide 2.95" and where belt sits 48.895mm (1.925")wide. Fits all Dynamos and 15mm Diameter shaft 16ACR Alternators.
Owing to the cost many use 12A1772 which is 79mm 3.1" wide - [lin...
24.5-25.5cc combustion chamber for use with flat top pistons. This specification of cylinder head is the only modified version for the small-bore based engines Mini Spares supply as it is judged to be the only one worth up-grading to. Based on used c...
37mm(1.457") longer inlet valve for the 2012 on 8 port head only
for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol
3.933" 99.898mm long
35.6mm(1.4") longer exhaust valve for the 2012 on 8 port head only
for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol--For earlier heads see C-AHT376/7 valves.
Valves now longe...
The original Special Tuning head 8 port head by Jim Whitehouse is the ULTIMATE Push rod head for the "A"Series has now been revamped and made available with larger inlet valves and special seats available to special order.Ports and combustion chamber...
Alloy 8 Port Head with 37.mm inlet valves with springs/top caps built up to take .500 thou cam lift with approximately 21cc combustion chamber.
The valve springs used are C-AEA526 with a fitted length of 1.350"
for the ...
Block gasket set for all mpi cars (1997on).10 gaskets and 3 seals only
This expensive gasket set was Rovers answer to leaking A plus blocks on the MPI cars to save any warranty costs, using latest Klinger type gaskets where applicable to avo...
Classic Castrol 20W/50 oil supplied in retro style 1 litre metal tin.
Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does
EN24 Nickel Chrome moly steel studs,Competition head stud kit.
torque to 45ftlbs -no need to re-torque cometic type head gaskets.
For use on the 2012 onwards heads only.
For use with 8 port cylinder head only
Rally/ race billet cam cross drilled and to original ST profile of C-AEG595 Sprint cam cross drilled and tuftrided-
A plus slot drive only -all our testing found this cam to give...
For use with 8 port cylinder head only
Road billet cam cross drilled and tuftrided- to old 544 (C-AEG643)profile
A plus slot drive only
C-AEG599 spider drive original sprint cams whilst socks last
[li...
Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.
Mahle RACE quality std size shells as used by competition engine builders.
for 1.75" big ends on 1275cc.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK. This is an up...
Mahle RACE quality std size shells as used by competition engine builders.
For 1.625" big ends on 998 and Cooper S.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in the UK. Th...
Mahle RACE quality std size main bearings 850/998cc PRE A PLUS only as used by competition engine builders..Quantity required-1 set.
RACE quality bearing set being made at the Mahle Motorsport Race Bearing Division Vandervell F1 plant in ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.