Showing 81 to 100 of 980

LARGE ALLOY HEAVY DUTY ALTERNATOR BRACKET FOR ALL PRE A PLUS ENGINES(PRE 1980) AS USED ON ABINGDON ST WORKS CARS

I've never broken a main bearing cap bolt, but then when I build a high performance engine I like to replace them as they stretch.

Sold singly 6 required per engine.

Brass type core plug for engine. Originally, engines had brass oilway plugs (2K1345) 1/4" hole fitted. These cup type plugs replaced them about 1985. 12.7mm cup type plug about 9.6mm deep. Fits 1/2" hole.

All good engine tuners ...

The 8 port head is taller than standard A series heads so these MGB short head studs are used on the front--4 3/8" long 3/8" UNC stud with unf end for head nut. These studs are also used for rod change gearbox differential housings.

[link}53...

The original ultimate engine stabilizer kit fits all 1275cc cylinder heads for RHD cars without a sandwich plate fitted. See MSSK1301 for sandwich plate type except Cooper cars 1990-2 that have PEQ10019 thermostat and 96 on ...

Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.

Sold singly,6 per c...

Too big for normal use, only used for special requirements. It is critical to understand that an oil cooler is not designed to last the life of the car. Sound maintenance practice tells us that whenever we are doing a major engine overhaul we should ...

Race profile billet cross drilled cam for the latest 2012 on 8 port head

A plus type drive with 310 inlet and 296 exhaust.

Triple groove collets for small bore. 1.043" (26.5mm) Dia x 3.44"(26.5mm) exhaust valve for all small bore castings.

Our race valves are produced in EN214N steel and require Manganese/Silicon bronze alloy valve guides. They are stellite tipp...

Oil pressure relief valve spring for Cooper S 1961 to 1971.

Identified by its pink band this is for the right or rear carb on twin set ups

as standard on Cooper and S versions--a longer version of feed pipe for twin HS4 carbs is AUD9102



20 degree float ang...

Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.

Made in Poly this mounting comes in 2 halves held by a large clip which helps engine removal. We will honestly state that they are not easy to fit and are thicker than the originals which causes a bit more grief. Longer bolts maybe required as well. ...

Top locking plate for 2A258 screw on rocker posts.

Deleted on some later cars but 2A515 can be used by elongating central hole to accept the 2A258 plug screw.

Very important shim to go behind crankshaft timing gear to align both wheels up and get correct alignment/true running of timing chain. Approx 5 thou thick, fit as many shims as required.

Genuine Mini Spares product to original drawings and specifications but NOT the original supplier as sold by Rover. The last Rover type supplied were very poor fitting copies where the holes were not correct and the rubber was of spurious quality.

Unpainted crank pulley for high performance engines, an efficient crank damper is a necessity to reduce failure. The standard damper commonly used is barely adequate for the standard engine. Mini Spares has reproduced the original "S" damper and pull...

original rocker shaft spring (3) between rockers on every A series engine

Distributor drive shaft.


A great deal of timing scatter can be traced to a worn gear at the inside end of the dizzy drive but if yours has been lost or broken the 12G4499MS secondhand used units will get you out of trouble.

The original mini upper engine steady that always needs the bushes replacing (they are CRC5329) and the longer of the 2 securing bolts, if it looks worse for wear or broken, is BH605151.

From 1990 on when the 1275 ...

Arrow previous
Arrow next
3 4 5 6 7 ...